VOYAGE DATA RECORDER Model VR-3000 SIMPLIFIED

VOYAGE DATA RECORDER
Model VR-3000
SIMPLIFIED VOYAGE DATA RECORDER
Model VR-3000S
Installation Manual
SAFETY INSTRUCTIONS ............................................................................................... i
EQUIPMENT LISTS........................................................................................................ ii
SYSTEM CONFIGURATION ......................................................................................... iv
RECORD OF PUB REV., PROG. NO.............................................................................. v
1. MOUNTING ............................................................................................................... 1
1.1 System Overview .....................................................................................................................1
1.2 Data Collecting Unit .................................................................................................................2
1.3 Data Recording Unit.................................................................................................................5
1.4 Junction Box ............................................................................................................................6
1.5 Remote Alarm Panel ................................................................................................................7
1.6 Microphone ..............................................................................................................................8
1.7 VHF Interface Unit IF-5200 (option) ....................................................................................... 12
2. WIRING.................................................................................................................... 13
2.1 System Wiring........................................................................................................................ 13
2.2 Data Collecting Unit ............................................................................................................... 14
2.3 Data Recording Unit (connecting IEEE1394 cable) ............................................................... 30
2.4 Junction Box .......................................................................................................................... 35
2.5 Remote Alarm Panel .............................................................................................................. 37
2.6 Microphone ............................................................................................................................ 38
2.7 Sensor Data ........................................................................................................................... 40
2.8 VHF Interface Unit ................................................................................................................. 44
2.9 Installation of Interface Board for Radar ................................................................................ 45
3. SETUP ..................................................................................................................... 46
3.1 VHF Interface Unit ................................................................................................................. 46
3.2 Data Collecting Unit ............................................................................................................... 47
3.3 DIP Switches in Junction Box ................................................................................................ 48
3.4 Recording Expiration Date of Parts........................................................................................ 51
3.5 System Time Adjustment ....................................................................................................... 52
PACKING LISTS..........................................................................................................A-1
OUTLINE DRAWINGS.................................................................................................D-1
INTERCONNECTION DIAGRAMS..............................................................................S-1
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
All rights reserved.
Printed in Japan
A : APR . 2006
N1 : FEB . 24, 2015
Pub. No. IME-44370-N1
( TAYA )
VR-3000/3000S
0 0 0 1 7 4 7 2 2 1 2
SAFETY INSTRUCTIONS
CAUTION
WARNING
Turn off the power at the switchboard
before beginning the installation.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage the equipment.
Standard
compass (m)
Steering
compass (m)
DCU
2.15
1.35
JB
1.65
1.05
DRU
1.10
0.65
Microphone
0.55
0.35
Waterproof
Microphone
1.05
0.70
VHF I/F unit
0.75
0.50
RAP
0.85
0.55
Do not disassemble or modify the
equipment.
Fire, electrical shock or injury may result.
Connect the power cable to correct
terminals.
Improper connection may result in
electrical shock, fire or injury.
Use the proper power supply.
The rated voltage for this equipment is
24 VDC and 100-230 VAC. Use of a
different power supply can damage the
equipment.
Attach grounding securely
to ship's body.
The grounding is required
to prevent electrical shock.
i
EQUIPMENT LISTS
Standard supply
Name
Data Collecting
Unit
Data Recording
Unit
Remote Alarm
Panel
Junction Box
Microphone
Waterproof
Microphone
Installation
Materials
Accessories
Spare Parts
Type
Code No.
Qty
VR-3010
—
1
VR-5020-9G
—
1
9 GB, for connection of 2-4
radars
VR-3016
—
1
Includes installation materials
IF-8530
VR-5011
—
—
1
Option on VR-3000S
VR-3012W
—
CP24-00605
CP24-00609
004-383-250
004-383-290
CP24-00601
004-383-210
CP24-00801
1 to 6
Remarks
Choose quantity
1
For VR-3010, radar 1 to 2 CH
For VR-3010, radar 3 to 4 CH
For VR-3010, no radar
connection.
004-384-960
1
For VR-3016
CP24-00217
CP24-00215
CP24-00910
CP24-00920
CP24-00930
004-381-090
004-379-590
000-042-241
000-042-242
000-016-261
1
1
FP24-00401
001-014-480
1
FP24-00201
FP24-00203
SP24-00201
004-383-300
004-555-560
004-555-540
1
1
1
For VR-5011
For VR-5020
IEEE1394 cable, 30m, w/armor
IEEE1394 cable, 20m, w/armor
IEEE1394 cable, 25m, w/armor
Label for RAP, 24-009-2901
(Code No. 100-338-891-10), 1 pc
English document
For VR-3010
For VR-3010
1
For detailed information about installation materials, accessories and spare parts, see the
packing lists at the end of this manual.
ii
Optional supply
Name
VHF Interface
Unit
LAN cable set
Removable Hard
Disk Drive
Waterproof
Microphone
Microphone
Junction Box
RGBHV cable
Battery
Radar I/F
Installation
materials
(for connecting
radar)
Radar Video
Switch Interface
Gland Gasket
Type
Code No.
IF-5200
000-040-789
CP03-28900
CP03-28910
000-082-658
000-082-659
CP03-28920
000-082-660
VR-3011-A
001-173-390
Remarks
To combine mic and loudspeaker
lines
10 m For installation of
20 m IF-8530, w/connector
MP5588-C,
30 m
FR-FTPC-CY (10 m)
VR-3012W
VR-5011
IF-8530
BNCX5-DSUB15-L400
BNCX5-DSUB15-L700
OP24-12
RI-3010
CP24-01200
CP24-01210
IF-1000RVC
OP24-16
000-041-946
000-159-595-10
000-159-596-10
004-385-010
000-010-132
Max. 3 total
For connection of radar video
signal, max. 4
2 sets
For receiving radar video signal
See Chapter 2.
000-010-133
—
001-046-260
See operator’s manual
IF-1000RVC
See page 34
iii
SYSTEM CONFIGURATION
Data Recording Unit (DRU)
VR-5020-9G
Waterproof MIC
VR-3012W
Analog (max.16ch)
Bridge MIC
VR-5011
Max. 6 ch
VHF I/F
IF-5200
Max. 2 ch
VHF Audio
IEC61162
Serial data
Digital (max.64ch)
Data Collecting
Unit (DCU)
VR-3010
Remote Alarm
Panel (RAP)
VR-3016
or
Alarm Monitoring
System
No. 1
Radar
PC
Live Player V4
VR-3020
Junction Box (JB)
IF-8530*
Radar I/F
RI-3010*
24 VDC
Serial (max.8ch)
Analog (max.16ch)
Digital (max.64ch)
Radar Video
SW Interface
IF-1000RVC
No. 2
Radar
Junction Box (JB)
IF-8530 (max.2)
HUB
Serial (max.8ch)
Serial (1ch)
100-230 VAC
24 VDC
Standard supply equipment and cable
Optional supply equipment and cable
Local supply equipment and cable
*: Optiopnal with VR-3000S
GPS
Speed log
Echo sounder
Autopilot
Engine telegraph
Steering gear
M/E remote system
Main air compressor
Bow thruster
Shell door system
Watertight doors
Fire doors
Anemometer
Fire detection
Main alarms
Others
Environmental category
Waterproof MIC
DRU
RAP
Bridge MIC
DCU
VHF I/F unit
JB
Radar Video SW Interface
Exposed to weather
Protected from weather
Note: For S-VDR, where it is impossible to obtain radar data, then AIS target data should be
recorded as a source of information from other ships. (Ref. IMO Res.MSC.163(78), section
5.4.7).
iv
Record of PUB REV., PROG. No.
Revision No.,
Date of Revision
Program No.
(software)
Outline of Revision
A
Apr. 19, 2006
VR-3000 SYSTEM
2450031-01
RAP
2450026-01
Same as above
1st printing.
A1 (For BSH)
June 2, 2006
p. iv
Added MIC VR-3012W to optional supply.
p. v, vi
Revised illustrations to show VR-3012W.
p. 10, 11, 38
Added mounting and wiring procedures for
VR-3012W.
p. 13, 14
Revised illustrations to show VR-3012W.
D-5, D-6
Added VR-3012W’s outline drawings.
S-1, S-2
Added VR-3012W to interconnection diagrams.
B: June 16, 2006
Same as above
All pages revised.
C: Aug. 21, 2006
Same as above
Added cover for the beacon.
D: Oct. 4 2006
Same as above
Added installation material for connecting radar.
E: Jan. 18, 2007
Same as above
For Russian TA: added PSU-011.
F: Aug. 2, 2007
Same as above
For second alarm
G: May 15, 2008
Same as above
Added IF-1000RVC for option.
H: Aug. 27, 2008
Dec. 15, 2008
VDR: 2450031-02
RAP/AP: Same as above
Added OP24-16 for option.
J: Mar. 14, 2010
Same as above
Page 30, 31
Revised the illustration.
K: Sep. 17, 2010
Same as above
Page ii
Changed the length of IEEE1394 cable to 20 m.
Page iii
Added 1394M1A1 L = 25 M.
L: Dec. 10, 2010
Same as above
Page ii
Added IEEE1394 cable 25 m, 30 m.
Page iii
Deleted 1394M1A1 L=25M, 30M.
M: May. 31, 2012
M1: Jul. 17, 2012
N: Apr. 12, 2013
Same as above
Deleted the PSU-001.
Same as above
Same as above
Minor change.
Changed the chassis of the PCB case.
v
This page is intentionally left blank.
vi
1. MOUNTING
NOTICE
Do not apply paint, anti-corrosive sealant
or contact spray to coating or plastic
parts of the equipment.
Those items contain organic solvents that
can damage coating and plastic parts,
especially plastic connectors.
1.1 System Overview
The basic VDR consists of
• Data Collecting Unit (DCU)
• Data Recording Unit (DRU) in the protective capsule
• Remote Alarm Panel (RAP) which indicates the status of the system remotely.
• Junction Box (JB) which can minimize the cable run and increase the number of the input
ports. (Optional supply with VR-3000S.)
• Bridge microphone (one supplied, max. 6)
• Optional VHF Interface Unit IF-5200 which combines VHF microphone and loudspeaker
lines.
The VDR system continuously stores data over past 12 hours in the DRU and removable hard
disk. Oldest data is erased as new data is entered.
The VDR operates on 100-230 VAC mains and 24 VDC power supply. In case of ship’s mains
failure, backup batteries are used for recording bridge audio for 2 hours.
A lot of sensors are connected to the VDR, in different signal types in some cases. Determine
all sensors to be connected before installation.
Note: The Data Collecting Unit, Data Recording Unit, Remote Alarm Panel and Junction Box
are sometimes referred to by their acronyms.
Data Collecting Unit: DCU
Data Recording Unit: DRU
Remote Alarm Panel: RAP
Junction Box: JB
1
1.2 Data Collecting Unit
The DCU is designed for on-deck or bulkhead installation, and should be mounted within the
wheelhouse. Mount it in a place convenient for connection with relevant sensors and associated
devices. For bulkhead mounting, be sure the mounting location is strong enough to support the
weight of the unit under the vibration normally encountered onboard the vessel. Be sure to
mount the DCU in an area with low humidity and away from high temperature materials, as well
as an area with minimal vibration and shock.
Eye bolts are provided at the top of the unit to hoist the unit onboard. Remove them after
installation and plug eye bolt holes with supplied cosmetic caps.
1.2.1 General mounting considerations
Mount the DCU considering the following points.
• The mounting surface must be flat. If it is not flat, insert a number of washers between the
unit and the mounting surface as necessary.
• The mounting location should be away from places subject to water splash and rain.
• Choose the location considering cable lengths, connection of relevant sensors and
associated devices, access to connectors and the unit’s door.
• A magnetic compass will be affected if the DCU is placed too close to a magnetic compass.
Observe the compass safe distances on page ii to prevent deviation of the compass.
• Observe the recommended service clearances shown in the outline drawing.
2
1.2.2 Mounting dimensions, mounting procedure
Fasten the unit to the chosen location with M10 bolts or ø10 coach bolts.
Bend radius
150 mm
Clamping point
300 mm or more
Mounting dimensions of DCU
3
1.2.3 Attaching card holder to door
A card holder for convenient storage of LAN cable, IEEE1394 cable, Error code table and Data
extraction procedure on the door of the DCU is available. Remove paper from double-sided
tape on the card holder and attach it to the door at the location shown below, aligning bottom
edge of card holder with bottom edge of door.
Card
holder
DCU door
4
1.3 Data Recording Unit
The DRU contains a protective capsule and it should be installed in the vicinity of the bridge on
the open deck area of the vessel. This will maximize the probability of its survival and facilitate
recovery following an incident. The DRU should be positioned clear of rigging and other
potential obstructions and as near to the centerline of the ship as possible. Constructing a
“fence” around the DRU is recommended.
1.3.1 Installation considerations
•
•
•
•
•
•
Must be separated from fuel or other potential fire hazards.
Must be separated from probable sources of mechanical damage.
Must be separated at least 4m from VHF/MF/HF antenna.
Must be installed in a place that facilitates routing maintenance and copying of recorded data.
Must be installed where a diver or remote operated vehicle could remove and retrieve.
There should be a clear and unobstructed area around the DRU to allow a diver or an ROV to
work.
1.3.2 Fixed-type DRU
Mounting
The DRU comes with the mounting bracket fitted. Request shipyard to construct a mounting
base for the DRU. (An example of one is shown on page 33.) On the mounting base, mount the
bracket with M8 bolts and nuts (double nuts). The gap between vibration absorber and bolt
should be at least 3 mm.
Projection
Acoustic beacon
Band
Gap
More than 3 mm
Vibration absorber
Cradle
Projection
A
A: details
Note: If you once detach the main body from the mounting bracket, fix the main body as shown
in the figure above so that the acoustic beacon is horizontal. Then, the main body is securely
fixed by the band.
How to detach the main body
1. Remove two snap pins.
2. Remove two hinge pins.
3. Lift the release levers and detach the main body.
Release lever
Hinge pin
Snap pin
5
1.4 Junction Box
The Junction Box, optionally available with the VR-3000S, provides for connection of digital,
serial and analog equipment, and three units may be connected. The No. 1 JB has the following
channels: Eight channels of IEC 61162 (two IEC 61162-2 and six IEC 61162-1), 64 channels of
digital, and 16 channels of analog. The No. 2 and No. 3 JBs have 64 channels of digital and 16
channels of analog, respectively.
1.4.1 Mounting considerations
The JB can be mounted on a bulkhead or a deck. For bulkhead mounting, be sure the mounting
location is strong enough to support the weight of the unit. Mount the JB considering the
following points.
• Locate the unit out of sunlight and away from heat sources because of heat that can build up
inside the cabinet.
• The mounting location should be away from places subject to water splash and rain.
• Choose the location considering cable lengths, connection of relevant sensors and
associated devices, and easy access to connectors inside.
• A magnetic compass will be affected if the JB is placed too close to it. Observe the compass
safe distances on page i to prevent deviation of a magnetic compass.
• Observe the recommended service clearances shown in the outline drawing.
1.4.2 Mounting dimensions, mounting procedure
17
12
Fasten the unit to the mounting location with M10 bolts or ø10 coach bolts.
Mounting dimensions of junction box
6
1.5 Remote Alarm Panel
Make sure there is a sufficient space for access to the rear cover for mounting and cabling. The
Remote Alarm Panel is flush-mounted. See the outline drawing for cutout size.
FIX UNIT WITH SELF-TAPPING SCREWS.
SET CAPS AFTER FASTENING SCREWS.
Mounting dimensions of Remote Alarm Panel
Attach the IMPORTANT label (large or small one supplied in accessory) near the remote alarm
panel.
IMPORTANT label
24-009-2901
7
1.6 Microphone
1.6.1 Bridge microphone VR-5011
The bridge microphone comes with a flush mount plate. Fix
the plate with six 4x16 self-tapping screws. The microphone
covers an area about 10 m in diameter with the height of 2 m.
Six microphones can cover a maximum 60 m diameter
bridge area (including wings).
2m
About 10 m
Coverage of microphone
Example of microphone at
radar station
Microphone mounting considerations, mounting dimensions
The following consideration must be taken into account to decide the location of the
microphone.
• Provide clearance around it (normally overhead in the bridge)
• The microphone is not waterproof, therefore do not install it on a wing.
• Locate away from noise sources, such as fans, motors, and loudspeakers (1 m or more from
air duct)
• Mount on a non-vibrating surface to keep noise to a minimum.
• Secure the cable to keep noise to a minimum. If the cable runs on an overhead without
securing it, the cable will pick up noise.
• Observe the compass safe distances shown on page i to prevent interference to a magnetic
compass.
• Microphones are mounted in the place(s) to pick up voices at the locations shown below.
(Complying with IEC 61996, 4.6.5.)
1) Centerline conning
2) Bridge wings (if steering gear is installed)
3) Main radar
4) Chart table
5) Helmsstand
6) Radio room
8
Mounting dimensions of Microphone VR-5011
9
1.6.2 Waterproof microphone VR-3012W
The waterproof microphone VR-3012W may be mounted on a wing, and is available in
bulkhead and flush mount versions.
Mounting considerations
The following consideration must be taken into account to decide the location of the waterproof
microphone.
• Provide sufficient clearance around the unit for maintenance, etc., referring to the outline
drawing.
• Locate away from noise sources, such as fans, motors, and loudspeakers (1 m or more from
air duct).
• Mount on a non-vibrating surface to keep noise to a minimum.
• Observe the compass safe distances shown on page i to prevent interference to a magnetic
compass.
• Secure the cable to keep noise to a minimum. If the cable runs on an overhead without
securing it, the cable will pick up noise.
Bulkhead mount
80±0.5
4-φ8
FIXING
HOLES
#150
215
13±5
195±0.5
1. Fasten the unit to the mounting location with M6 bolts or ø6coach screws.
2. See “Bulkhead mount” in paragraph 2.6.2 for wiring procedure.
100
#50
CABLE ENTRY
69
77
#50
Mounting dimensions for bulkhead mount VR-3012W
10
Flush mount
1. Prepare a cutout (120x60 mm) in the mounting location, referring to the outline drawing.
2. Dismount the microphone chassis from the case to detach MIC assy.
Leave the rubber gasket attached to the MIC assy. The case may be discarded.
3. Pass wiring through the cover assy. (supplied).
4. Wire the microphone referring to paragraph 2.6.
5. Set the cover assy. to the MIC assy. and fasten with two screws.
6. Set the entire assy. to the mounting location and fasten with 12 self-tapping screws (4x16).
7. Coat area around the MIC assy. with silicone sealant to enhance waterproofing.
Gasket
Mounting dimensions for flush mount VR-3012W
11
1.7 VHF Interface Unit IF-5200 (option)
Mounting
Fix the unit using 4x20 self-tapping screws. Remove the cover to access to holes. When a
non-FURUNO VHF is connected to the unit, using the terminal board, remove unused wires
and connectors. Otherwise, noise problem may arise.
Audio level is adjusted by DIP switches in the interface unit after installation. See paragraph 3.1.
116 ± 0.5
4- φ 5
(FIXING HOLES)
NAMEPLATE
148
176 ± 0.5
217
#50
94
Mounting dimensions of VHF interface unit
12
#50
2. WIRING
2.1 System Wiring
Data Recording Unit (DRU)
VR-5020-9G
IEEE1394 cable
(20m, 25m or 30m, w/ armor)
Waterproof MIC
VR-3012W
TTYCS-4
(max. 6 ch) Data Collecting
VHF I/F
Unit (DCU)
IF-5200
VR-3010
TTYCS-1
(max. 2 ch)
Bridge MIC
VR-5011
VHF Audio
No. 1
Radar
*3
No. 2
Radar
*3
TTYCS-4
Radar Video
SW Interface
IF-1000RVC
PC
Live Player V4
VR-3020
*3
LAN cable
STP(CAT5)
DPYC-2.5
Alarm Monitoring
System
Radar I/F
RI-3010*
DPYC-1.5
DPYC-1.5
TTYCS-1 x 6*1
TTYCS-1Q x 2*2
IEC61162
Serial data
LAN cable
STP(CAT5)
100-230 VAC
24 VDC
*1: IEC 61162-1
*2: IEC 61162-2
*3: KB-HD152K or 3COX-2P-6C
Cable names (Japan Industrial Standard,
equivalent may be used) are shown along
cable lines together with number of cables
required.
: Standard supply equipment and cable
:Optional supply equipment and cable
:Local supply equipment and cable
*: Optiopnal with VR-3000S
Digital (max.64ch)
TTYCS-1
Remote Alarm
Panel (RAP)
VR-3016
HUB
3C2V or 5C2V
(max. 4 ch)
Radar
TTYCS-4
Analog (max.16ch)
TTYCS-1
Serial (1ch)
Junction Box (JB)
IF-8530 (max.2)
or
Junction Box (JB)
IF-8530*
DPYC-1.5
24 VDC
Serial (max.8ch)
TTYCS-1 x 6*1
TTYCS-1Q x 2*2
Analog (max.16ch)
TTYCS-1
Digital (max.64ch)
TTYCS-1
GPS
Speed log
Echo sounder
Autopilot
Engine telegraph
Steering gear
M/E remote system
Main air compressor
Bow thruster
Shell door system
Watertight doors
Fire doors
Anemometer
Fire detection
Main alarms
Others
13
2.2 Data Collecting Unit
2.2.1 Location of connectors and terminals
Radar video
connectors (4)
beneath this
plate
Side of the PCB case:
J33 (KEYBOARD)
J28 (VGA)
J24 (RS232C)
Playback/CPU SW
DRU (Reserved for
future use)
From left:
J8 (DRU)
J6 (Playback)
J14 (Data)
From top:
TB10 (MIC5)
TB11 (MIC6)
TB12 (VHF1)
TB13 (VHF2)
From left:
TB3 (24VDC OUT)
J10 (JB)
From top:
1
TB14 (CH1* )
1
TB15 (CH2* )
TB4 (RAP)
2
TB5 (AMS* )
Cable Clamps
Lead in cables
thru appropriate
cable slots
referring to
front view of
cable clamp.
1
* IEC61162-2
2
* Alarm Monitoring
System
From top:
TB1
TB6 (MIC1)
(100-230 VAC IN)
TB7 (MIC2)
TB2
TB8 (MIC3)
(24 VDC IN)
TB9 (MIC4)
From top:
TB16 (CH3)
TB17 (CH4)
TB18 (CH5)
TB19 (CH6) IEC61162-1
TB20 (CH7)
TB21 (CH8)
Cables for MICs
AMS,
RAP
LAN,
IEEE1394
Power cables
Radar video cables
14
Cables for
serial equipment
Connectors, terminals, etc. inside the DCU
Terminals and connectors in the DCU
Connector/TB
Signal/Unit to be connected
TB1 (100-230 VAC IN)
100-230 VAC
TB2 (24 VDC IN)
24 VDC
TB3 (24 VDC OUT)
24 VDC for JB
TB4 (RAP)
Remote Alarm Panel
TB5 (AMS)
Alarm Monitoring System
TB6-TB11 (MIC1-MIC6)
Bridge audio, 6 channels
TB12-TB-13 (VHF1-VHF2)
VHF audio, 2 channels
TB14-TB21 (CH1-CH8)
Serial data, 8 channels
J6 (PLAYBACK)
Play back data/PC
J8 (DRU)
DRU
J10 (JB)
JB
J14 (DATA)
Live Player V4 VR-3020
J24 (RS232C)
PC
J28 (VGA)
Monitor
J33 (KEYBOARD)
Keyboard
DRU
Reserved for future use
For service
Refer to the interconnection diagram for details of pins on the terminal boards. Turn off the DCU
before making connections.
Note 1: The DCU and DRU are connected to each other with the supplied IEEE1394 (sometimes
called FireWire*) cable on which two plugs are factory-fitted at both ends. These plugs look like
the same but these are different; one has latches and the other does not. These are labeled
“DCU” and “DRU,” so connect the cable accordingly.
*FireWire is a registered trademark of the Apple Corporation. It was originally developed as a
very fast external bus technology that supports data transfer rates of up to 400Mbps.
Note 2: Attach cable band (supplied) to each cable to be connected to the DCU and record
sensor name/equipment name on each cable band.
15
2.2.2 Working inside the unit
Snap/wire assembly for keeping door of DCU open
A snap/wire assembly which keeps the door of the DCU open while working inside the DCU is
provided. Use it to keep the door open and prevent deformation of the door when it is opened.
Attach one snap to the hole on the door and the other snap to the hole to the right of the battery
handle. Note that it is not necessary to detach the assembly before closing the door.
This procedure is necessary only when the unit is mounted on the deck.
Attach the snap
to these holes.
Snap/wire assembly
16
Lead-fitting tool
Radar, MIC, VHF, etc. are connected to the terminals and connectors in the DCU. The terminal
board has WAGO connectors for leads of up to 2.5 mm2 or AWG 14 wires. Use the lead-fitting tool,
attached inside the DCU, to fix wires to WAGO connectors, as shown in the illustration below.
Lead fittting tool
How to use lead-fitting tool
1) Strip sheath by 8-10 mm.
3) Tug on wires to confirm that they are securely
inserted.
2) Use lead-fitting tool to open terminal and then insert wire.
17
2.2.3 Cable fabrication
DPYC-1.5, DPYC-2.5 (power cables)
3
L=150
Armor
Armor
Sheath
Sheath
Cut the sheath.
50
 = 11.7 mm
Conductor
S = 1.5 mm2
 = 1.56 mm
Remove paint.
DPYC-1.5 cross section view
Armor
15 10
6
Sheath
Vinyl tape
 = 12.5 mm
Conductor
S = 2.5 mm 2
 = 2.01 mm
Crimp-on lug
FV2-4
(supplied)
1
DPYC-2.5 cross section view
Fabrication of cable type DPYC-1.5, DPYC-2.5 (or equivalent)
TTYCS-1 (Serial equipment, format IEC 61162-1)
L=300
Shield
50
Armor
Remove paint
by 50 mm.
Cut vinyl sheath.
Sheath
Shield
 = 10.1 mm
Expose cores, trim shield,
solder ground wire to
shield, attach crimp-on lug
to ground wire.
Conductor
S = 0.75 mm 2
 = 1.11 mm
TTYCS-1 cross section view
Vinyl tape
6
Lay this part in cable clamp.
Fabrication of cable type TTYCS-1(or equivalent)
18
TTYCS-1Q (Serial equipment, format IEC 61162-2)
L=300
50
Armor
Shield
Remove paint
by 50 mm.
Cut vinyl sheath.
Sheath
 = 11.3 mm
Expose cores, trim shield,
solder ground wire to
shield, attach crimp-on lug
to ground wire.
Shield
Conductor
S = 0.75 mm 2
 = 1.11 mm
TTYCS-1Q cross section view
Vinyl tape
6
Lay this part in cable clamp.
Fabrication of cable type TTYCS-1Q (or equivalent)
TTYCS-4 (Alarm Monitoring System, MIC, RAP, analog equipment)
L=300
Shield
50
Armor
Remove paint
by 50 mm.
Cut vinyl sheath.
Sheath
 = 16.3 mm
Shield
Conductor
S = 0.75 mm2
 = 1.11 mm
Expose cores, trim shield,
solder ground wire to
shield, attach crimp-on lug
TTYCS-4 cross section view
to ground wire.
6
Vinyl tape
Lay this part in cable clamp.
Fabrication of cable type TTYCS-4 (or equivalent)
Note: For crimp-on lugs for TTYCS cables, use those on respective terminal board.
19
How to process armor of IEEE1394 cable
Ground the armor of the IEEE1394 cable by the cable clamp at the DCU. Fabricate the cable as
follows.
1. Confirm the label “DCU” at the end of the
cable end. (Fabricate the cable at the DCU
side.)
2. Use a box cutter to cut and remove the heat-shrink tube and remove the vinyl sheath approx.
8 cm from the end of the cable.
Approx. 8cm
Heat-shrink tube
3.
Wind the vinyl tape at the end of armor about 2 cm in width so that the end of the armor is
centered on the winding.
2cm
Completed state
End of armor
20
2.2.4 Power supply
Connect the DCU unit as follows:
• AC power: Connect the ship’s mains to “100-230 VAC IN” in the DCU with cable DPYC-1.5 (or
equivalent). If AC emergency source of electrical power is provided, connect it to the AC line.
• DC power: If no AC emergency source of electrical power is provided, connect the ship’s
battery to “24 VDC IN” (max10A battery) in the DCU with cable DPCY-2.5 (or equivalent).
Observe the polarity when connecting DC source.
• Junction Box: Connect the DCU to the Junction Box with cable DPYC-1.5.
Main Generator
VDR
AC
DC
Emergency Generator
Ship equipped with emergency AC power
VDR
AC
Main Generator
DC
Battery
Ship has no emergency AC power
Power connections and ship’s power arrangement
Power connections in the DCU
Terminal
TB1 (100-230 VAC IN)
TB2 (24 VDC IN)
TB3 (24 VDC OUT)
Pin No.
Signal Type
1
AC LINE
2
AC NEUT
3
AC GND
1
DC INPUT+
2
DC INPUT-
1
DC OUTPUT+
2
DC OUTPUT-
Remarks
Connect to TB1 (24 VDC IN) on
JB
2.2.5 Ground
Connect a ground wire (IV-8sq) between the
ground terminal on the unit and ship’s grounding
bus. Make the length as short as possible.
CAUTION
Attach grounding securely
to the ship's body.
The grounding is required
to prevent electrical shock.
21
2.2.6 Radar RGB video
Interlaced or non-interlaced radar video (4 ch max.) is connected to the video connectors on the
RADAR I/F Board (optionally available with the VR-3000S) inside the DCU, with a 15-pin VGA
Male to 5x BNC RGBHV cable. (Cable is supplied with VR-3000, and is available optionally with
the VR-3000S.) The system supports separate sync, sync-on-green, and composite sync signals.
1)
Video signal level: 0.5 to 1 Vpp
(Minimum sync signal is 50 mV when a composite sync signal is used.)
2)
Horizontal sync signal: Max. 91.146 kHz, positive or negative
3)
Vertical sync signal: Max. 85 Hz
Receivable resolution is 640 x 480 to 1280 x 1024 as shown in table below.
(a)
VGA:
640 x 480
(f)
FR-15x5M3 series:
1024 x 780
(b)
Wide VGA:
852 x 480
(g)
FAR-28x5 series:
1066 x 800
(c)
CCIR:
738 x 576
(h)
Wide XGA:
1336 x 768
(d)
SVGA:
800 x 600
(i)
SXGA:
1280 x 1024
(e)
Wide SVGA:
1067 x 600
(j)
FR-21x5 series:
1280 x 1024
Attach connector assemblies (BNCX5-DSUB15-L400 and BNCX5-DSUB15-L7400) following the
illustration on the next page. Connect coaxial cables after attaching connector assemblies. If
coaxial cables are to be supplied locally, use type 3C-2V or 5C-2V. (Five cables are required.) A
“single cable” (CP24-01200 or CP24-01210) for connection of radar is optionally available.
Type
CP24-01200
CP24-01210
22
Coaxial cable
1.5C2V-3C2V-T-20 m
(20 m, 6 coaxial cores, large dia. for RGB,
small dia. for HV)
1.5C2V-3C2V-T-30 m
(30 m, 6 coaxial cores, large dia. for RGB,
small dia. for HV)
Coaxial connector
1) FB-SPM1D (BNC-P-3), 3 pcs.
2) BNC-P-1.7N, 3 pcs.
1) FB-SPM1D (BNC-P-3), 3 pcs.
2) BNC-P-1.7N, 3 pcs.
Connection of radar video signal in DCU
2 4
Bind cables with cable tie.
1 3
Fix the cable with this cable clip.
Cable assy.
BNCX5-DSUB-L700
(length: 700 mm)
Connector arrangement on
RADAR I/F Board
Cable assy.
BNCX5-DSUB-L400
(length: 400 mm)
Fix the ground wire with the screw.
Tape BNC connector with
vinyl insulating tape.
23
Cable arrangement in cable clamp and coaxial cable type
3C-2V coaxial cable
5C-2V coaxial cable
Five coaxial cables
Five coaxial cables bound with
cable tie, inside and outside the DCU.
24
Attaching coaxial connector
Washer
Clamping nut
Gasket
1) Slip clamping nut, washer and gasket onto cable.
Center
pin
5) Insert center pin to core and solder.
7 mm
Shell
2) Strip sheath by 7 mm.
6) Screw shell into cable.
3 mm
3) Strip shield and insulator by 3 mm.
Completed
4) Slide clamp onto cable and fold back shield onto clamp.
25
FAR-21x7/28x7 series radar
For the connection between the VR-3000 and FAR-21x7/28x7 series radar, refer to the respective
radar installation manual.
FR-21x5 series radar
Modify the FR-21x5 series radar as shown below to connect it to the VR-3000/VR-3000S.
Parts of FR-21x5 series radar modification kit
Parts Name
Type
Code No.
Qty
RGB buffer kit
RGB-BUFF board
NH-XH connector assy.
NH-XH connector assy.
OP03-162
03P9229A
NH10P-XH13P
NH4P-XH3P
008-501-130
1 set
BNC connector converter
DSUB-BNC-1
000-148-528
1
2 m RGB cable
KB-HD152K
000-152-099
1
INT board
RGB-BUFF board
XH13P
J449
RGB cable, 2m
J1
BNCx5
J2
NH10P
DB15 DB15
J449
XH3P
J463
-
J3
NH4P
BNC connector converter
FR -21x5 Display Unit
Modification on FR-21x5 series radar
26
FAR/FR-28x5 series radar
Modify the FAR/FR-28x5 series radar as shown below to connect it to the VDR.
Parts of FAR/FR-28x5 series radar modification kit
Parts Name
VDR I/F kit (1)
RGB-BUFF board
NH-XH connector assy.
NH-XH connector assy.
VDA/INT chassis
VDR I/F kit (2)
(No VDA/INT chassis)
BNC connector converter
2 m RGB cable
Type
OP03-177
03P9229A
03-2057, 4-3P
03-2058, 10-13P
03-133-1127-4
OP03-178
Code No.
008-528-270
008-528-280
DSUB-BNC-1
KB-HD152K
000-148-528
000-152-099
Qty
1 set
1
1
Kit (1): For display units being produced in June 2002 and before.
Kit (2): For display units being produced in July 2002 and after.
INT board
J449
-
03-2058
RGB-BUFF board
XH13P
J1
BNCx5
NH10P
J2
XH3P
J463
-
RGB cable, 2m
DB15
DB15
J3
NH4P
03-2057
BNC connector converter
FR/FAR-28x5 Display Unit
Modification on FAR/FR-28x5 series radar
The figure below illustrates how to mount CPA/TCPA board together with RGB buffer board in
FAR/FR-28x5 series radar. VDA/INT chassis should be new type, 03-133-1127-3. CPA/TCPA
board is powered from #6 (12V) and #8 (GND) of DTB-2. J463 on INT board is used for RGB
board.
Use 15 mm spacers.
CPA/TCPA board
Use 25 mm spacers.
This hole is not used.
VIDEO AMP
New VDA/INT chassis
RGB board
Mounting PA/TCPA and RGB boards in FAR/FR-28x5
27
2.2.7 Alarm Monitoring System (AMS)
The Alarm Monitoring System connects to TB5 in the DCU, with cable TTYCS-4 (see page 19 for
cable fabrication and cable construction). Three types of signals are generated: system failure,
local ACK and remote ACK. See the figure below and the two on the next page for details.
System failure
VR-3000/VR-3000S notifies the AMS that an alarm has been generated. Use NC port.
TB5
Contact Rating
Voltage: less than 32 V
Current: Less than 0.2 A
1
NC
NC: Normal Closed Contact
2
COM
500 ms
Alarm stop
System failure
ON
Buzzer
OFF
Normal condition
Buzzer
Alarm activated
Alarm occured
Alarm activated
Another alarm occured
ACK
ACK
(2nd alarm)*
Buzzer stop
Alarm continued
*: When error code 086 or 084 occurs, system failure can not be output by 2nd alarm.
Local ACK
VR-3000/VR-3000S notifies the AMS that it has acknowledged system failure.
TB5
Contact Rating
Voltage: less than 32 V
Current: Less than 0.2 A
NC
4
NC
5
NO
COM
NC: Normal Close Contact
NO: Normal Open Contact
Close
Open
6
NO
Close
Open
500 ms
Local Ack
Active
Active interval of Local ACK
signal is 500 msec ±5 msec.
Local ACK signal
28
Remote ACK
AMS notifies the VR-3000/VR-3000S that it has acknowledged system failure.
+24 V
NO
7 3.3 K
+
NC
8 3.3 K
C
C
C
C
Active
A
> 150 ms
Total impedance (contact and cable)
shall be less than 500 ohms.
NC: Normal Close Contact
NO: Normal Open Contact
B
> 150 ms
A
> 150 ms
Active interval A and B of Remote ACK
signal shall be more than 150 msec.
Chattering may be present at interval C .
Choose close or open contact with S1#4 on
AP MAIN board (24P0075B)
ON=Normal Close
OFF=Normal Open (default)
Remote ACK signal
S1
29
2.3 Data Recording Unit (connecting IEEE1394 cable)
Connect the DRU and DCU with the IEEE1394 cable (20 m, 25 m, or 30 m). The cable is
attached the connectors at both ends. The connectors are labeled “DCU” and “DRU,”
respectively; do not confuse the connectors.
For the IEEE1394 cable, keep in mind the following points.
•
•
•
•
Do not cut the cable.
If welding of cable gland or cabling support is necessary, weld BEFORE running cable.
Take care not to damage shield of cable.
The connector connected to the DCU must be protected from rain. If necessary, run the cable
through conduit or the like.
• Remove the connector cap and cap bracket from the DRU connector.
How to connect the cable to the DRU
DRU connector
The connector cap and cap bracket are attached
to the DRU connector and fixed with vinyl tape.
1. Remove vinyl tape, connector cap and cap
bracket from the DRU connector perfectly.
Be careful not to damage the DRU
connector when removing parts.
Vinyl tape, connector cap and cap bracket are
removed perfectly.
Cap nut
Rubber bushing
Teflon washer
30
The cap bracket is NOT removed.
2. Pass the cap nut, teflon washer and rubber
bushing onto the cable as shown left.
3. Grease inside and outside of
rubber bushing with supplied
lubricant. This allows for
the rubber bushing/cable and
rubber bushing/DRU connections
to slide easily.
4. Coat threads with lubricant to prevent
scorching of threads. DO NOT coat the connector.
5. Confirm that the connector does not
have a notch then connect it to
receptacle on the DRU.
6. Push the cable towards the DRU then
put the teflon washer and rubber
bushing on to the cable.
DO NOT pull the cable. The connector
does not have a fastening notch to
prevent it from being disconnected.
31
7. Coat the surface of the teflon washer
and connecting part of the cable
with supplied silicone sealant.
Gap: Approx. 2.6 mm
Gap:
Approx.
2.6 mm
approx.
1 thread
Thread
DO NOT OVERTIGHTEN Thread
screw OR
How to tighten cap nut
8. Tighten the DRU cap nut until the cap nut
contacts the surface of the DRU. The cap nut
is correctly tightened if approx. one thread of
the cap nut is visible.
Gap: Approx. 2.6 mm
Gap between cap
n
9. Coat the area around the cable connection
and the cap nut with silicone sealant for
waterproofing.
32
How to fix the DRU to the mounting base
- Mounting base "A" to be supplied
by shipyard.
- Fix the DRU on the compass deck.
- Select the location where the DRU
can be easily maintained.
- Locate well away from other equipment.
A
Loop: >30cm
- Do not cut the cable even if it is too long.
- Loop the cable and bind it with cable ties.
Then fix the cable near the DRU but
do not fix to the handle.
- Fix the cable between the DRU and loop
with cable ties.
The radius of the loop must be more than
15 cm.
Do not loop the cable around the
handle of the DRU to keep the radius of
the loop more than 15 cm.
Fix the rocker pins.
33
How to connect the cable to the DCU
Connect the cable to the DRU port J8 in the DCU and fix it with a cable tie. Using vinyl tape, tape
from tip of connector to about 8 cm.
Fix the cable to the support plate with the cable tie.
Optional Kit
The optional kit is provided for the IEEE1394 cable run through the deck.
Name: Gland gasket OP24-16, Code number: 001-046-260
Name
Type
Code No.
Qty
Gasket
24-004-1503
100-347-370-10
1
Washer
24-004-1504
100-347-380-10
4
34
2.4 Junction Box
Connect the junction box to the DCU before turning on the system.
2.4.1 Location of connectors
Navigation device, etc. are connected to the terminals and connectors on the terminal board in
the JB. The terminal board has WAGO spring-catch terminal blocks for leads of up to 2.5 mm2 or
AWG 14 wires.
Insert wires into holes in the connectors the same as on the terminal board in the DCU.
SERIAL OUT CH1 (for additional JB)
DIP SW from left:
S5 (JB No.)
S4 (Baud Rate)
S3 (Baud Rate)
S2 (Analog)
S1 (Analog)
DCU
CH5
CH6
CH7
CH8
CH13-CH16
CH21-CH24
CH29-CH32
CH37-CH40
CH45-CH48
CH53-CH56
CH1
CH2
CH13-CH16
CH4
CH5-CH8
CH3
CH61-CH64
CH1
CH5-CH8
SERIAL CHANNELS
DIGITAL
CHANNELS
Serial
Spare
LAN
Spare
Serial
Digital
Serial
Analog
Digital
CH9-CH12
CH1-CH4
CH57-CH60
CH49-CH52
CH41-CH44
CH33-CH36
CH25-CH28
CH17-CH20
CH9-CH12
CH1-CH4
ANALOG
CHANNELS
DC 24V IN
Power Supply
Analog
Location of connectors inside the junction box, where to lead in cables thru cable clamps
35
2.4.2 Cable fabrication
Cable type DPYC-1.5 (power), TTYCS-1 and TTYCS-1Q (serial IEC 61162-1 and IEC 61162-2,
respectively), and TTYCS-1 (analog) connect various equipment to the JB. For fabrication of
those cables, see paragraph 1.1.3.
2.4.3 Ground
Connect a ground wire (IV-8sq) between the ground terminal on the unit and ship’s grounding
bus.
CAUTION
Attach grounding securely
to the ship's body.
The grounding is required
to prevent electrical shock.
2.4.4 Connection of additional junction boxes
Maximum two additional junction boxes may be installed. An additional junction box has
connections for 1 serial channel (IEC 61162-1, CH3 only), 64 digital channels, and 16 analog
channels. See the figure below for general wiring.
When installing additional junction boxes, set junction box no. (2 and 3) with DIP SW S5. If the
junction box no. of additional junction boxes is left as “1”, data will not be output from the junction
box. For setting procedure, see page 50.
No. 1 Junction Box
(standard supply)
24 VDC Serial: 8CH
Analog: 16CH
Digital: 64CH
LAN cable Serial CH 1 to CH8
24 VDC
172.31.24.1
Data Collecting
Unit
No. 1 Junction Box
(standard supply)
(V2.xx
V1.5xx)
SW
HUB
Data Collecting
Unit
Connection of one Junction Box
Only CH3 (serial input) can
be used with No.2 and No.3
Junction Boxes.
Serial: 1CH
Analog: 16CH
Digital: 64CH
No. 2 Junction Box
Serial: 1CH
Analog: 16CH
Digital: 64CH
No. 3 Junction Box
Connection of two or three Junction Boxes
36
V1.05
and
after
2.5 Remote Alarm Panel
A
- Clamp armor of cable.
- Connect shield to shield screw on back panel.
- Connect Wago connector to terminal after removing
chip to avoid damage to terminal.
- Spacer "A" is not necesary when space is too wide as
in A above.
- Tape fabricated part of cable with vinyl tape.
A
Wiring RAP
37
2.6
Microphone
A maximum of 6 microphones can be connected, to TB6 thru TB11 in the DCU. A dual twisted,
balanced cable carries the following signals:
+: 24 VDC (+)
A: Audio signal line, balanced, 0 dBm
B: Audio signal line, balanced, 0 dBm
-: 24 VDC (-)
MIC1 audio is mixed with MIC2 audio, MIC3 with MIC4, and MIC5 with MIC6, respectively.
CAUTION: Turn off the DCU before connecting a microphone, to prevent damage to the
microphone.
2.6.1 VR-5011
- Refer to page 19 for cable fabrication.
- Connect shield to screw on chassis as shown.
- Tape fabricated part of cable with vinyl tape.
38
NOTICE
After installing microphones, test them
to make sure they are not picking up
noise and that the sound quality is good.
2.6.2 VR-3012W
Bulkhead mount
1. Unfasten the cover.
2. Lead in wiring through the cable gland and connect it to the terminal board on the rear side
the cover, referring to the interconnection diagram. See page 19 for how to fabricate the cable.
Be sure to ground shield. Tape fabricated part of wiring with vinyl tape.
3. Close the cover.
Flush mount
1. Connect wiring to the terminal board on the rear side of the cover, referring to the
interconnection diagram. See page 19 for how to fabricate the cable. Be sure to ground shield.
Tape fabricated part of wiring with vinyl tape.
2. Fasten the cover to the housing.
NOTICE
After installing microphones, test them
to make sure they are not picking up
noise and that the sound quality is good.
39
2.7 Sensor Data
Note: The serial channels in the Junction Box IF-8530 can receive the maximum of 82 characters
in a sentence, consisting of a maximum of 79 characters between the starting delimiter "$" or “!”
and the terminating delimiter <CR>, <LF> as defined by NMEA0183/IEC61162.
2.7.1 IEC 61162-1 serial data
12 channels are provided to receive IEC 61162-1 serial data, six in the DCU and six in the JB.
Receivable are all IEC 61162 sentences and binary data, but at least ZDA is necessary for
stamping date and time.
Data Collecting Unit
A
B
IEC 61162-1 interface circuit in Data Collecting Unit
Junction Box
A
A
B
IEC 61162-1 interface circuit in Junction Box
40
2.7.2 IEC 61162-2 serial data
4 channels are provided to receive IEC 61162-2 serial data, two in the DCU and two in the JB.
Data Collecting Unit
G
B
A
IEC 61162-2 interface circuit in Data Collecting Unit
Junction Box
B
A
G
IEC 61162-2 interface circuit in Junction Box
41
2.7.3 Non-IEC 61162 signal
1) Analog
4 to 20 mA, 0 to 10 V and –10 to +10 V signals (max. 16 channels) can be connected to the
ANALOG terminals in the JB. Input voltage (current) range is set by DIP switches in the junction
box.
Voltage signal
The voltage between two input terminals is 0 to +10V or –10 to +10 V.
Current signal
For 4 to 20 mA current signal set jumper between I and V as shown below.
Connect for current signal
V
470 ohms
1/2W
I
G
Connection of 4-20 mA current signal
2) Digital (Voltage and Contact-closure)
The terminals for digital input in the JB connect voltage and contact-closure signals. Range of
input voltage is 10 to 32 V. The system sends 24 VDC to ”floating contact.”
The figures below show the digital interface circuit for voltage and contact-closure signals
respectively.
10-32 V
+24 V
2.2 K
24
2.2 K
A
B
G
Interfacing of voltage signal
42
+24 V
2.2 K
24
Jumper
2.2 K
A
B
G
Interfacing of contact-closure signal
Note: Jumpers are fitted at factory between A and 24 terminals for CH1 to CH32 in order to
connect contact-closure signal. To connect a voltage signal to CH1 to CH32, remove
jumper by using two openers attached inside the junction box. To connect a
contact-closure signal to CH33 to CH64, short between A and 24 terminals by using a
jumper wire (local supply).
43
2.8 VHF Interface Unit
Two VHF audio signals may be connected to the terminal board in the DCU. IMO requires one
VHF audio to be recorded. A dual twisted, balanced cable carries the following signals:
+: 24 VDC (+)
A: Audio signal line, balanced, 0 dBm
B: Audio signal line, balanced, 0 dBm
-: 24 VDC (-)
The VHF interface unit mixes VHF transmitting and receiving signals for the VDR. When the VHF
outputs the mixed signal, this unit is not required.
Specifications
Power Supply:
Mic input level:
24 VDC (21.6 to 31.6 VDC), 40mA
-16 to –56 dBm, Input impedance: >10k ohms
(Factory default: -46 dBm, 600 ohms: 10dB ATT ON)
32 to 200 ohms, 2 mW, input impedance: 10k ohms
(Factory default: 2 mW, 200 ohms: 10dB ATT OFF)
TTL level
0 dBm±10dB, 600 ohms, balanced
Speaker input level:
PTT Switch signal:
Output:
When a wing handset is used, the connection is made as follows.
HANDSET
IF-5200
FM-8700
CN3 CN1 CN2
DC24V
FM10PS-6H
TTYCS-1
*
HANDSET
VR-3000 DCU
CC490, 1m
CN4
WING
HANDSET
FM14-7P
OUT1**
CN7 CN5 CN6
*
CC491, 1m
*
TTYCS-1
OUT2**
TB12
TB13
CN9
*
CN8
TTYC-4S
WING
HANDSET
X2
**: OUT2 can be mixed with OUT1.
*: Connect one of OUT1 or OUT2. Fix cable with a cable tie
inside of the chassis.
Connecting FM-8700 to DCU via interface unit IF-5200
44
2.9 Installation of Interface Board for Radar
When the interface board for connection of radar(s) is not installed at the factory, install it (in the
DCU) as shown below.
1. Remove ten screws shown below to detach the PCB.
2. Remove the screws shown below to remove the fixing plate.
Remove this screw
to remove the fixing plate.
Fixing plate
PCB card case
3. Connect the flat cable between the two interface boards if it is not already connected.
4. Set the boards in the PCB card case as shown below.
Fix boards
with screws.
Set larger
board in slot.
5. Fix the boards with the screws provided.
6. Reattach the fixing plate and PCB card case.
7. Connect cabling as shown on page 21-24.
45
3. SETUP
This chapter describes how to set up and check the system.
3.1 VHF Interface Unit
3.1.1 Audio level adjustment
DS1 and DS3 are 10 dB step attenuators for channel 1 and 2 microphone lines respectively. Set
the DIP switch so that the audio output level between #4 and #5 (OUT1) and between #7 and #8
(OUT2) of CN9 is 0 dBm (2.2 Vp-p).
Factory-setting: 10 dB (ON); 20 dB (OFF); 30 dB (OFF) and 40 dB (OFF).
DS1
CN9
JP1
Channel 1 Input
DS2
#4
#5
OUT1
#7
#8
OUT2
To VDR
DS3
Channel 2 Input
DS4
Location of DIP switches and jumper wire in VHF interface unit
Functions of #1 and #2 segments of DS2 and DS4
Segment # of DS2 and DS4
Function
#1 (10 dB ATT)
Attenuates speaker signal by 10 dB. Factory-setting: OFF
#2 (MIX)
When set to OFF, either “mic” or “sp” signal is sent to the VDR
according to the PTT switch status. When ON, both “mic” and
“sp” signals are always sent to the VDR. Factory-setting: OFF
3.1.2 Jumper setting
Jumper wire JP1 functions as follows:
• Short circuit (Factory-setting): “Input” signals from CH1 and CH2 are output from OUT 1 port
and OUT 2 port, respectively.
• Open circuit: “Input” signals from CH1 and CH2 are output from OUT 1 port.
46
3.2 Data Collecting Unit
The system configuration must be updated after installation. See instruction manual for VDR
Maintenance Viewer and operator’s manual for Live Player V4 for the procedure.
The outline of the system configuration is;
Step 1: Network setting on PC
Step 2: Connection of PC
Step 3: Software configuration
Step 4: Making a backup copy of configuration data
Step 5: Software configuration from file data
Step 6: Media management
Step 7: Other functions
47
3.3 DIP Switches in Junction Box
DIP switches in the JB are provided to set up the system according to equipment connected. The
default setting for all DIP switches is “OFF”.
Turn off the VR-3000/S and junction box to change the DIP switch setting. After setting the DIP
switches, turn on the system to apply the settings.
DIP SW from left:
S5 (JB No.)
S4 (Baud Rate 1)
S3 (Baud Rate 2)
S2 (Analog 1)
S1 (Analog 2)
Junction box, inside view
Analog signal (DIP SW S1, DIP SW S2)
Analog Signal Range Setting
Channel
SW No.
SW Label
CH1
S2-1
1
OFF
ON
CH2
S2-2
2
OFF
ON
CH3
S2-3
3
OFF
ON
CH4
S2-4
4
OFF
ON
CH5
S2-5
5
OFF
ON
CH6
S2-6
6
OFF
ON
CH7
S2-7
7
OFF
ON
CH8
S2-8
8
OFF
ON
CH9
S1-1
9
OFF
ON
CH10
S1-2
10
OFF
ON
CH11
S1-3
11
OFF
ON
CH12
S1-4
12
OFF
ON
CH13
S1-5
13
OFF
ON
CH14
S1-6
14
OFF
ON
CH15
S1-7
15
OFF
ON
CH16
S1-8
16
OFF
ON
48
-10V to +10 V
0 V to +10 V or 4-20 mA
Serial data baud rate (DIP SW S3, S4)
Use for No. 1 JB (Set S5-6, S5-7, S5-8 as OFF, OFF, OFF.)
Channel
*1
CH1
*1
CH2
*2
CH3
*2
CH4
*2
CH5
*2
CH6
*2
CH7
*2
CH8
Serial Baud Rate Setting (bps)
SW No.
SW
Label
4800
9600
19200
38400
S4-1
1A
OFF
—
—
ON
S4-2
1B
OFF
—
—
ON
S4-3
2A
OFF
—
—
ON
S4-4
2B
OFF
—
—
ON
S4-5
3A
OFF
ON
OFF
—
S4-6
3B
OFF
OFF
ON
—
S4-7
4A
OFF
ON
OFF
—
S4-8
4B
OFF
OFF
ON
—
S3-1
5A
OFF
ON
OFF
—
S3-2
5B
OFF
OFF
ON
—
S3-3
6A
OFF
ON
OFF
—
S3-4
6B
OFF
OFF
ON
—
S3-5
7A
OFF
ON
OFF
—
S3-6
7B
OFF
OFF
ON
—
S3-7
8A
OFF
ON
OFF
—
8B
OFF
OFF
ON
—
S3-8
*1
*2
IEC 61162-2, IEC 61162-1
When serial out CH1 of No. 2 or No. 3 JB is connected to CH3 to CH8 of previous JB, set the CH
switch for 19200 bps.
Use for No.2, No. 3 JB. (Set S5-6, S5-7, S5-8 as OFF, OFF, ON or OFF, ON, OFF.)
Channel
*2
CH3
Serial Baud Rate Setting (bps)
SW No.
SW
Label
4800
9600
19200
38400
S4-5
3A
OFF
ON
—
—
S4-6
3B
OFF
OFF
—
—
*2
IEC 61162-1
Only CH3 functions on JB No. 2 and No. 3.
49
Junction box no. setting (DIP SW S5)
JB No.
1
JB DIP SW
S5-6: OFF
S5-7: OFF
S5-8: OFF
2
S5-6: OFF
S5-7: OFF
S5-8: ON
3
S5-6: OFF
S5-7: ON
S5-8: OFF
JB IP Address
172.31.24.10
S5-1: OFF
S5-2: OFF
S5-3: OFF
S5-4: OFF
172.31.24.11
S5-1: ON
S5-2: OFF
S5-3: OFF
S5-4: ON
172.31.24.12
S5-1: OFF
S5-2: ON
S5-3: OFF
S5-4: ON
JB NW Mode
S5-5: OFF
S5-5: ON
S5-5: ON
nd
rd
No. 2, No. 3 JB: Additional junction boxes (2 or 3 JB)
50
3.4 Recording Expiration Date of Parts
After installing and setting up the system, record the expiration date of major parts of the system,
on the sheet provided. Cut out (or copy and cut) an expiration data sheet from the ones below.
For interval-specific parts record date of expiration and for general consumable parts the date of
replacement. Place the card in the card holder on the inside of the door of the DCU. The
expiration period starts from date of installation.
Card holder
Interval-specific parts
Life
Battery in DCU
4 years
Underwater acoustic beacon in DRU
6 years
General consumable parts
Life
Backup HDD
2 years
Removable HDD (VR-3011-A)
10 years
DC power fan
6 years
6 years
DCU chassis fan
AC power supply
Interval-specific parts
Date of replacement
6 years
Life
Battery in DCU
4 years
Underwater acoustic beacon in DRU
6 years
General consumable parts
Life
Backup HDD
2 years
Removable HDD (VR-3011-A)
10 years
DC power fan
6 years
6 years
DCU chassis fan
AC power supply
Date of expiration
Date of expiration
Date of replacement
6 years
51
3.5 System Time Adjustment
The system time, used for time-stamping VDR data, synchronizes with the UTC time if the system
time is behind the UTC time within one hour. However, the system time is set to within two
minutes (typically 10 seconds) behind the UTC time after installation to make the synchronization
faster.
1. Connect VGA monitor and keyboard to the DCU, at the locations shown below.
Inside of the DCU
Side view of th PCB case
Connect the VGA monitor to
the VGA connector (J28).
Connect the keyboard to
the USB connector.
DCU, door opened
2.
3.
4.
5.
6.
7.
52
Turn on the VR-3000 while pressing and holding down the F2 key.
Wait for the BIOS screen to come up. (Keep the F2 key pressed.)
Set the system time about 10 seconds behind UTC or GPS time.
Press F10, Y, and Enter keys in order to save data.
Restart VR-3000.
Wait until system time synchronizes with the GPS time.
NAME
004-383-290-00
CP24-00609
004-383-250-00
CP24-00605
004-555-560-00
FP24-00203
004-383-300-00
FP24-00201
004-383-310-00
FP24-00202
004-555-540-00
SP24-00201
000-042-169-00
VR-3010/3010-S-I/N
**
DESCRIPTION/CODE №
(*2)
1
(*2)
1
1
(*1)
1
(*1)
1
1
1
Q'TY
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
2.(*1)(*2)は、それぞれ仕様選択品を表します。
(*1)(*2)INDICATE SPECIFICATION SELECTIVE ITEM.
NAME
DOCUMENT
OUTLINE
1/1
**
**
**
**
(*3)
1
1
1
1
(*2)
1
Q'TY
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF
THE UPPER PRODUCT. QUALITY IS THE SAME.
24AE-X-9851
型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。
000-169-588-1*
OMJ-44373-*
000-157-079-1*
IM*-44370-*
000-157-088-1*
OS*-44370-*
000-157-077-1*
OM*-44370-*
004-383-210-00
CP24-00601
DESCRIPTION/CODE №
24AE-X-9851 -6
3.(*3)の取扱説明書は、ｻｰﾋﾞｽﾏﾝが持ち帰ります。
(*3) OPERATOR'S MANUAL SHOULD BE RETURN TO ENGINEER.
OPERATOR'S MANUAL
取扱説明書(和)
INSTALLATION MANUAL
装備要領書
OPERATOR'S GUIDE
操作要領書
OPERATOR'S MANUAL
取扱説明書
図書
INSTALLATION MATERIALS
工事材料
VR-3010/3010-S-I/3010-S-N
1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
INSTALLATION MATERIALS
工事材料
OUTLINE
INSTALLATION MATERIALS
ACCESSORIES
SPARE PARTS
UNIT
INSTALLATION MATERIALS
工事材料
工事材料
ACCESSORIES
付属品
ACCESSORIES
付属品
ACCESSORIES
付属品
付属品
SPARE PARTS
予備品
予備品
DATA COLLECTING
UNIT(DCU)
ﾃﾞｰﾀ収集ﾕﾆｯﾄ
ユニット
ＰＡＣＫＩＮＧ　ＬＩＳＴ
A-1
12'4#6145/#07#.
ขᛒ⺑᣿ᦠ
⧷
%&41/
%&41/
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
1/'
%1&'01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
C4437-F01-D
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
ฬ‫ޓޓ‬⒓
0#/'
DATA EXTRACTION
PROCEDURE
ﾃﾞｰﾀﾁｭｳｼｭﾂﾖｳﾘｮｳ
ERROR CODE TABLE
ｴﾗｰｺｰﾄﾞﾋｮｳ
CARD HOLDER
ｶｰﾄﾞﾎﾙﾀﾞｰ
LAN CABLE ASSEMBLY
LANｹｰﾌﾞﾙ(ﾌﾞﾙｰ)
CABLE
ｹｰﾌﾞﾙ(IEEE1394)
名　称
NAME
略　図
OUTLINE
000-151-843-00
000-165-407-10
000-155-571-00
000-159-488-1*
CODE
NO.
000-159-489-1*
C42-00408-*
CODE
NO.
C42-00407-*
CODE
NO.
C-26-ﾀﾃ-ﾆ-1
000-159-485-00
C-26-ﾀﾃ-ﾆ-1
CODE
NO.
ALT-03BX
CODE
NO.
FP24-00203
1
1
1
1
1
数量
Q'TY
004-555-560-00
型名／規格
DESCRIPTIONS
AIE896
TYPE
CODE NO.
用途／備考
REMARKS
24AE-X-9503 -2
1/1
A-3
ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.
（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
C4437-F03-C
型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
5
4
3
2
1
番 号
NO.
ACCESSORIES
⇟ภ
01
#%%'5514+'5
付属品表
(2
6;2'
A-2
#': ઃዻຠ⴫
%1&'01
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
%#$.'‫ޓ‬6+'
㩄㩧㩗㩨㨹㩂㩇
%#$.'‫ޓ‬6+'
㩄㩧㩗㩨㨹㩂㩇
%15/'6+%%#2
㩘㩨㩣㩎㩁㨶㨹㩖㩩
%100'%614‫ޓ‬#55;
㩄㩒㩂㩊⚵ຠ
%100'%614‫ޓ‬#55;
㩄㩒㩂㩊⚵ຠ
%#$.'$#0&
㩃㨺㩖㩨㩣㩔㩨㩧㩎㩨
50#29+4'#55'/$.;
㩇㩏㨹㩖㩩㩦㨼㩞㨺㩂㩚㩕㩧
%4+/210.7)
࿶⌕┵ሶ
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
%80
%1&'01
%80
%1&'01
%2$%+814;
%1&'01
$0%:&57$.
%1&'01
$0%:&57$.
%1&'01
2.(//
%1&'01
1#.
%1&'01
(8$.7
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
C4437-M03-G
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
C4437-M02-G
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
A-5
#': 6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
%1&'01
%2$%+814;
%1&'01
$0%:&57$.
%1&'01
$0%:&57$.
%1&'01
2.(//
%1&'01
1#.
%1&'01
(8$.7
%1&'01
%80
%1&'01
%80
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
%15/'6+%%#2
㩘㩨㩣㩎㩁㨶㨹㩖㩩
%100'%614‫ޓ‬#55;
㩄㩒㩂㩊⚵ຠ
%100'%614‫ޓ‬#55;
㩄㩒㩂㩊⚵ຠ
%#$.'$#0&
㩃㨺㩖㩨㩣㩔㩨㩧㩎㩨
50#29+4'#55'/$.;
㩇㩏㨹㩖㩩㩦㨼㩞㨺㩂㩚㩕㩧
%4+/210.7)
࿶⌕┵ሶ
%#$.'‫ޓ‬6+'
㩄㩧㩗㩨㨹㩂㩇
%#$.'‫ޓ‬6+'
㩄㩧㩗㩨㨹㩂㩇
⇛‫ޓޓ‬࿑
176.+0'
6;2'
%1&'01
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%2
6;2'
A-4
#': Ꮏ੐᧚ᢱ⴫
%1&'01
%15/'6+%%#2
㩘㩨㩣㩎㩁㨶㨹㩖㩩
%#$.'$#0&
㩃㨺㩖㩨㩣㩔㩨㩧㩎㩨
50#29+4'#55'/$.;
㩇㩏㨹㩖㩩㩦㨼㩞㨺㩂㩚㩕㩧
%4+/210.7)
࿶⌕┵ሶ
%#$.'‫ޓ‬6+'
㩄㩧㩗㩨㨹㩂㩇
%#$.'‫ޓ‬6+'
㩄㩧㩗㩨㨹㩂㩇
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
%2$%+814;
%1&'01
2.(//
%1&'01
1#.
%1&'01
(8$.7
%1&'01
%80
%1&'01
%80
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
#': 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
C4437-M04-F
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-6
0#/'
&1%7/'06
36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
C4418-Z02-D
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
'
%
%2
A-7
#$: &'5%4+26+10%1&'ͳ
84)
㪈㪅䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫ဳᑼ㪆䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪜㪛㩷㪙㪰㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪫㪰㪧㪠㪚㪘㪣㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
2#46+6+10241%'&74'
㩔㩩㨺㩍㨲㩆㨸㩧ᚻ㗅
176.+0'
+056#..#6+10/#6'4+#.5
70+6
%*#0)'%10(+)74#6+10/'07
%10(+)ᄌᦝ߅㗿޿
࿑ᦠ
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
&#6#4'%14&'4
㩍㩨㨺㩊⸥㍳ེ
࡙࠾࠶࠻
84))
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
(.7+&%1/2170&
㨿㨼㩣㩄㩧㩔㩩㨽㩧㩎㩨
5+.+%10'5'#.#06
㩆㩢㩄㩧㩄㩨㩛
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
-50
%1&'01
-'9
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
#$: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
C4418-M02-F
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-8
0#/'
176.+0'
+056#..#6+10/#6'4+#.5
#%%'5514+'5
70+6
%2
(2
84
36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
C4437-Z02-C
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
A-9
#': &'5%4+26+10%1&'ͳ
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
#%%'5514+'5
ઃዻຠ
ઃዻຠ
4'/16'#.#4/2#0'.
4#2
㩢㩝㨺㩎㨻㩡㨺㩛㩔㩩㩒㩣
࡙࠾࠶࠻
84*-
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
SELF-TAPPING SCREW
+ﾅﾍﾞﾀｯﾋﾟﾝﾈｼﾞ 1ｼｭ
CAP
ｷｬｯﾌﾟ
名　称
NAME
略　図
OUTLINE
CODE
NO.
000-162-659-10
000-809-321-00
4X30 SUS304 1ｼｭ
CODE
NO.
000-164-927-10
000-515-248-00
4X30 SUS304
040-3025
040-3025
型名／規格
DESCRIPTIONS
4
4
数量
Q'TY
CP24-00801
TYPE
用途／備考
REMARKS
24AE-X-9401 -1
1/1
ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.
（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
C4437-M01-B
型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
2
1
番 号
NO.
INSTALLATION MATERIALS
工事材料表
004-384-960-00
CODE NO.
A-10
0#/'
176.+0'
+056#..#6+10/#6'4+#.5
70+6
%2
84
36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
C4418-Z04-D
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
A-11
#$: &'5%4+26+10%1&'ͳ
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
/+%412*10'
㩙㨼㩂㩥㩖㨵㩧
࡙࠾࠶࠻
8484*-
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
1ｼｭ
SELF-TAPPING SCREW
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
名　称
NAME
略　図
OUTLINE
CODE
NO.
000-162-605-10
4X16 SUS304
型名／規格
DESCRIPTIONS
6
数量
Q'TY
CP24-00217
TYPE
用途／備考
REMARKS
24AB-X-9405 -2
1/1
ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.
（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
C4418-M05-C
型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
1
番 号
NO.
INSTALLATION MATERIALS
工事材料表
004-381-090-00
CODE NO.
A-12
0#/'
176.+0'
+056#..#6+10/#6'4+#.5
#%%'5514+'5
70+6
59㨻㩣㩚㩋㨷㨺㩖㩨)
%2
(2
(2
849
&'5%4+26+10%1&'ͳ
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
C4437-Z04-B
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
36;
A-13
#': ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
5+.+%1047$$'4
㩃㩚㩆㨺㩣
Ꮏ੐᧚ᢱ
#%%'5514+'5
ઃዻຠ
ઃዻຠ
9#6'42411(/+%412*10'
㒐᳓㩙㨼㩂
࡙࠾࠶࠻
849
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
524+0)9#5*'4
㩔㩨㩒㩅㩨㩀㩨㩒
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
2#0*'#&5%4'9
㩏㩗㩨ዊ㩒㩆㩨
%18'4‫ޓ‬#55;
㩀㩔㩨㨺⚵ຠ
ฬ‫ޓޓ‬⒓
0#/'
849
⇛‫ޓޓ‬࿑
176.+0'
9#6'42411(/+%412*10'
%1&'01
/%9
%1&'01
/%4
%1&'01
/:%9/$0+
%1&'01
(2
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
6;2'
ᢙ㊂
36;
A-14
↪ㅜ㧛஻⠨
4'/#4-5
#': 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
C4437-F05-C
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
#%%'5514+'5
ઃዻຠ⴫
%1&'01
FUSE
ﾋｭｰｽﾞ
ELECTRIC
CO.,LTD.
FGBO 125V 10A
PBF
DWG. NO.
OR
TYPE NO.
S
DWG NO.
PER
VES
2
SPARE
A-15
P
000-155-826-10
REMARKS/CODE NO.
SETS PER
VESSEL
BOX NO.
型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は
変わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
1/1
24AE-X-9301 -0 1/1
C4437-P01-A
QUANTITY
E
WORKING
PER
SET
U
SP24-00201
004-555-540-00
（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING　FOR REFERENCE ONLY.）
FURUNO
OUTLINE
SPARE PARTS LIST FOR
NAME OF
PART
MFR'S NAME
1
ITEM
NO.
SHIP NO.
TYPE
CODE NO.
D-1
Y. Hatai
D-2
Takahashi
D-3
Feb.25'05
D-4
D-5
Y. Hatai
Y. Hatai
D-6
Y. Hatai
D-7
D-8
16/May/08 R.Esumi
音声マイク
(最大６台)
注記
＊１）造船所手配
＊２）オプション
＊３）切断不可
MIC4
ウイング用
FOR WING
AUDIO MIC
(MAX. 6 SETS)
NOTE
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: NEVER CUT THE CABLE.
TTYCS-1 *1
VHF2
VHF1
DRAWN
7/Jan/2015
CHECKED
7/Jan/2015
APPROVED
SCALE
DWG No.
*1
DPYC-1.5
C4437-C01- P
J28
RED
GREEN
BLUE
NC
GND
AGND(R)
AGND(G)
AGND(B)
NC
GND
NC
CRT_DOC_DATA
H_SYNC
V_SYNC
CRT_DOC_CLOCK
J24
1 DCD
2 RXD
3 TXD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
J33
1 +5V
2 USB0- LOWER
3 USB0+
4 GND
SH FG
5 +5V
6 USB1- UPPER
7 USB1+
8 GND
SH FG
J32
データ収集ユニット
DATA COLLECTING UNIT
VR-3010
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
AC IN
TB1
1 L
2 N
3 G
DC IN
TB2
1 24V
2 0V
GND
BB+
AA+
1
2
3
4
5
6
P
P
IEEE1394
P
P
P
RADAR I/F
RI-3010
BNCX5-DSUB15-L400
*1
PE IV-8sq.
保護アース
REF.No.
T.YAMASAKI
H.MAKI
MASS
kg
24-009-5038-8
8/Jan/2015 H.MAKI
BNCX5-DSUB15-L400 *2
BNCX5-DSUB15-L700 *2
VGA4
R 1
G 2
B 3
R_GND 6
G_GND 7
B_GND 8
SYNC_GND 10
H_SYNC 13
V_SYNC 14
15
BNCX5-DSUB15-L700
VGA
RS-232C
CPU BOARD
USB KEYBOARD
(FOR MAINTENANCE)
D
各信号の接続に関しては造船所/船主との事前打合せが必要です。
CONSULT WITH SHIPOWNER AND/OR SHIPYARD ABOUT CONNECTION OF DEVICES.
TITLE
VR-3000
名称
航海情報記録装置
相互結線図
NAME
VOYAGE DATA RECORDER
INTERCONNECTION DIAGRAM
V
H
B
G
R
V
H
BNC
BNC
BNC
または OR
HUB
PC (LIVE PLAYER)
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21 *2 レーダーまたはECDIS
RADAR OR ECDIS
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21 *2 レーダーまたはECDIS
RADAR OR ECDIS
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21
レーダーまたはECDIS
RADAR OR ECDIS
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21
レーダーまたはECDIS
RADAR OR ECDIS
5
B
G
R
V
H
B
G
R
V
H
B
G
R
BNC
TB4
TD_A
TD_B
RD_A
RD_B
GND
+24V
OV
RJ45 J1
1 TX-P
P
2 TX-N
3 RX-P
4
P P
5
6 RX-N
7
P
8
DC IN
TB1
1 24V
2 0V
*1
STP CABLE(CAT5)
*1
STP(CAT5)
ALT-03BX,3m OR
STP-CAT5,CROSS(*1)
*1
DPYC-1.5
1
2
3
4
5
6
7
データ記録器
DATA RECORDING UNIT
VR-5020-9G
アラームモニタリングシステム
ALARM MONITORING SYSTEM
AIE896,2m(IEEE1394)
*1
TTYCS-4
*1
TTYCS-4
*3
1394M1A1 AG,20m,φ15
(25/30m:OPTION)
4
VGA3
R 1
G 2
B 3
R_GND 6
G_GND 7
B_GND 8
SYNC_GND 10
H_SYNC 13
V_SYNC 14
15
VGA1
R 1
G 2
B 3
4
5
R_GND 6
G_GND 7
B_GND 8
9
SYNC_GND 10
11
12
H_SYNC 13
V_SYNC 14
15
VGA2
R 1
G 2
B 3
R_GND 6
G_GND 7
B_GND 8
SYNC_GND 10
H_SYNC 13
V_SYNC 14
15
J10 RJ45
LAN1_BI_DA+ 1
LAN1_BI_DA- 2
LAN1_BI_DB+ 3
LAN1_BI_DC- 4
LAN1_BI_DC+ 5
LAN1_BI_DB- 6
LAN1_BI_DD+ 7
LAN1_BI_DD- 8
DC OUT
TB3
24V 1
0V 2
J14 RJ45
LAN2_BI_DA+ 1
P
LAN2_BI_DA- 2
LAN2_BI_DB+ 3
LAN2_BI_DC- 4
PP
LAN2_BI_DC+ 5
LAN2_BI_DB- 6
LAN2_BI_DD+ 7
P
LAN2_BI_DD- 8
TP
TP
TP
TP
J6
TB5
SYS_FAIL(NC) 1
SYS_FAIL(COM) 2
SYS_FAIL(NO) 3
LOCAL_ACK(NC) 4
LOCAL_ACK(COM) 5
LOCAL_ACK(NO) 6
REMOTE_ACK(+) 7
REMOTE_ACK(-) 8
P
P
P
IEEE1394
接続箱
JUNCTION BOX
IF-8530
100-230VAC
1φ,50/60Hz
*1
DPYC-2.5
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
1
2
3
4
5
6
3
24VDC
SERIAL CH8
IEC61162-1
SERIAL CH7
IEC61162-1
SERIAL CH6
IEC61162-1
SERIAL CH5
IEC61162-1
SERIAL CH4
IEC61162-1
SERIAL CH3
IEC61162-1
*1
TTYCS-1
*1
TTYCS-1Q
*1
TTYCS-1Q
*1
TTYCS-1
*1
TTYCS-1
P P
P P
J8
TB4
COM2 RX- 1
COM2 RX+ 2
COM2 TX- 3
COM2 TX+ 4
COM2 GND 5
+24V 6
OV 7
+24V
GND
TP BTP B+
TP ATP A+
2
SERIAL CH2
IEC61162-2
SERIAL CH1
IEC61162-2
VHF INTERFACE
IF-5200
VHF RECEIVER
(MAX. 2 ch)
VHF INTERFACE
IF-5200
同上
DITTO
C
1m
TTYCS-1 *1
MIC6
*1
TTYCS-4
*1
TTYCS-4
P P
P P
B
*1
TTYCS-4
*1
TTYCS-4
TB7
24V
A
B
OV
TB8
1 24V
2 A
3 B
4 OV
TB9
1 24V
2 A
3 B
4 OV
TB10
1 24V
2 A
3 B
4 OV
TB11
1 24V
2 A
3 B
4 OV
TB12
1 24V
2 A
3 B
4 OV
TB13
1 24V
2 A
3 B
4 OV
TB14
1 A1
2 B1
3 G1
TB15
1 A2
2 B2
3 G2
TB16
1 A
2 B
TB17
1 A
2 B
TB18
1 A
2 B
TB19
1 A
2 B
TB20
1 A
2 B
TB21
1 A
2 B
1
2
3
4
TB6
24V
A
B
OV
*1
IV-8sq.
VHF2
24VDC
同上
DITTO
MIC3
P P
P P
1
2
3
4
リモートアラームパネル
REMOTE ALARM PANEL
VR-3016
VHF1
24VDC
1m
同上
DITTO
MIC2
*1
TTYCS-4
*1
TTYCS-4
TERMINAL
BOARD(1)
MIC5
同上
DITTO
MIC1
1
2
3
4
5
A
マイクロフォン
MICROPHONE
VR-5011 または OR
防水型マイク *2
WATERPROOF MIC
VR-3012W
24V
マイクロフォン A
MICROPHONE
B
VR-5011
OV
1
6
S-1
注記
＊１）造船所手配
＊２）オプション
＊３）切断不可
音声マイク
(最大６台)
AUDIO MIC
(MAX. 6 SETS)
NOTE
*1. SHIPYARD SUPPLY.
*2. OPTION.
*3. NEVER CUT THE CABLE.
1m
各信号の接続に関しては造船所/船主との事前打合せが必要です。
CONSULT WITH SHIPOWNER AND/OR SHIPYARD ABOUT CONNECTION OF DEVICES.
TTYCS-1 *1
1m
VHF2
VHF1
DRAWN
7/Jan/2015
CHECKED
DWG No.
100-230VAC
1φ,50/60Hz
*1
DPYC-1.5
7/Jan/2015
APPROVED
H.MAKI
SCALE
MASS
C4436-C01- M
J28
RED
GREEN
BLUE
NC
GND
AGND(R)
AGND(G)
AGND(B)
NC
GND
NC
CRT_DOC_DATA
H_SYNC
V_SYNC
CRT_DOC_CLOCK
J24
1 DCD
2 RXD
3 TXD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
J33
1 +5V
2 USB0- LOWER
3 USB0+
4 GND
SH FG
5 +5V
6 USB1- UPPER
7 USB1+
8 GND
SH FG
J32
データ収集ユニット
DATA COLLECTING UNIT
VR-3010
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
AC IN
TB1
1 L
2 N
3 G
DC IN
TB2
1 24V
2 0V
P
P
IEEE1394
J10 RJ45
LAN1_BI_DA+ 1
LAN1_BI_DA- 2
LAN1_BI_DB+ 3
LAN1_BI_DC- 4
LAN1_BI_DC+ 5
LAN1_BI_DB- 6
LAN1_BI_DD+ 7
LAN1_BI_DD- 8
DC OUT
TB3
24V 1
0V 2
BNCX5-DSUB15-L400 *2
BNCX5-DSUB15-L700 *2
VGA4
R 1
G 2
B 3
R_GND 6
G_GND 7
B_GND 8
SYNC_GND 10
H_SYNC 13
V_SYNC 14
15
RADAR I/F
RI-3010 *2
BNCX5-DSUB15-L700 *2
VGA3
R 1
G 2
B 3
R_GND 6
G_GND 7
B_GND 8
SYNC_GND 10
H_SYNC 13
V_SYNC 14
15
BNCX5-DSUB15-L400 *2
VGA1
R 1
G 2
B 3
4
5
R_GND 6
G_GND 7
B_GND 8
9
SYNC_GND 10
11
12
H_SYNC 13
V_SYNC 14
15
VGA2
R 1
G 2
B 3
R_GND 6
G_GND 7
B_GND 8
SYNC_GND 10
H_SYNC 13
V_SYNC 14
15
*1
PE IV-8sq.
保護アース
REF.No.
T.YAMASAKI
kg
24-009-5038-8
VGA
8/Jan/2015 H.MAKI
RS-232C
V
H
B
G
R
V
BNC
BNC
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21 *2 レーダーまたはECDIS
RADAR OR ECDIS
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21 *2 レーダーまたはECDIS
RADAR OR ECDIS
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21 *2 レーダーまたはECDIS
RADAR OR ECDIS
5
H
B
G
R
V
H
B
BNC
COAX. CABLE(x5) (*1) OR
1.5C2V-3C2V-T-20M/30M
20/30m,φ21 *2 レーダーまたはECDIS
RADAR OR ECDIS
4
G
R
V
H
B
G
R
BNC
または OR
HUB
PC (LIVE PLAYER)
*1 RJ45 J1
STP CABLE(CAT5)
1 TX-P
P
2 TX-N
3 RX-P
4
P P
5
6 RX-N
7
P
8
DC IN
*1
TB1
DPYC-1.5
1 24V
2 0V
*1
STP(CAT5)
ALT-03BX,3m OR
STP-CAT5,CROSS(*1)
AIE896,2m(IEEE1394)
アラームモニタリングシステム
ALARM MONITORING SYSTEM
接続箱
JUNCTION BOX
IF-8530 *2
*1
DPYC-2.5
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
GND
BB+
AA+
1
2
3
4
5
6
J14 RJ45
LAN2_BI_DA+ 1
P
LAN2_BI_DA- 2
LAN2_BI_DB+ 3
LAN2_BI_DC- 4
PP
LAN2_BI_DC+ 5
LAN2_BI_DB- 6
LAN2_BI_DD+ 7
P
LAN2_BI_DD- 8
TP
TP
TP
TP
J6
P
P
P
*1
TTYCS-4
3
24VDC
SERIAL CH8
IEC61162-1
SERIAL CH7
IEC61162-1
SERIAL CH6
IEC61162-1
SERIAL CH5
IEC61162-1
SERIAL CH4
IEC61162-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1Q
*1
TTYCS-1Q
*1
TTYCS-1
*1
TTYCS-1
P P
TB5
SYS_FAIL(NC) 1
SYS_FAIL(COM) 2
SYS_FAIL(NO) 3
LOCAL_ACK(NC) 4
LOCAL_ACK(COM) 5
LOCAL_ACK(NO) 6
REMOTE_ACK(+) 7
REMOTE_ACK(-) 8
TB4
TD_A
TD_B
RD_A
RD_B
GND
+24V
OV
*1
TTYCS-4
1
2
3
4
5
6
7
データ記録器
DATA RECORDING UNIT
VR-5020-9G
*3
1394M1A1-AG
20/30m,φ15
2
SERIAL CH3
IEC61162-1
SERIAL CH2
IEC61162-2
SERIAL CH1
IEC61162-2
VHF INTERFACE
IF-5200
VHF RECEIVER
(MAX. 2 ch)
VHF INTERFACE
IF-5200
C
VHF2
24VDC
ウイング用
FOR WING
TTYCS-1 *1
同上
DITTO
P P
P P
P P
J8 IEEE1394
+24V 1
GND 2
TP B- 3
TP B+ 4
TP A- 5
TP A+ 6
TB4
COM2 RX- 1
P
COM2 RX+ 2
COM2 TX- 3
P
COM2 TX+ 4
COM2 GND 5
+24V 6
P
OV 7
*1
IV-8sq.
VHF1
24VDC
MIC6
*1
TTYCS-4
*1
TTYCS-4
*1
TTYCS-4
*1
TTYCS-4
TB7
24V
A
B
OV
TB8
1 24V
2 A
3 B
4 OV
TB9
1 24V
2 A
3 B
4 OV
TB10
1 24V
2 A
3 B
4 OV
TB11
1 24V
2 A
3 B
4 OV
TB12
1 24V
2 A
3 B
4 OV
TB13
1 24V
2 A
3 B
4 OV
TB14
1 A1
2 B1
3 G1
TB15
1 A2
2 B2
3 G2
TB16
1 A
2 B
TB17
1 A
2 B
TB18
1 A
2 B
TB19
1 A
2 B
TB20
1 A
2 B
TB21
1 A
2 B
1
2
3
4
TB6
24V
A
B
OV
リモートアラームパネル
REMOTE ALARM PANEL
VR-3016
MIC5
同上
DITTO
MIC4
マイクロフォン
MICROPHONE
VR-5011 または OR
防水型マイク *2
WATERPROOF MIC
VR-3012W
同上
DITTO
P P
P P
1
2
3
4
B
MIC3
*1
TTYCS-4
*1
TTYCS-4
TERMINAL
BOARD(1)
MIC2
1
2
3
4
5
A
同上
DITTO
MIC1
24V
マイクロフォン A
MICROPHONE B
VR-5011
OV
1
6
S-2
CPU BOARD
USB KEYBOARD
(FOR MAINTENANCE)
D
TITLE
VR-3000S
名称
簡易型航海情報記録装置
相互結線図
NAME
SIMPLIFIED VOYAGE DATA RECORDER
INTERCONNECTION DIAGRAM
1
2
接続箱 JUNCTION BOX IF-8530
DIGITAL
(CONTACT)
*1
CH1 TTYCS-1
A
CH2
CH3
CH4
CH5
CH6
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*3
*3
*3
*3
*3
*3
B
CH7
CH8
CH9
CH10
C
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
*3
*3
*3
*3
*3
CH11 TTYCS-1
CH12
CH13
CH14
CH15
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*3
*3
*3
*3
D
CH16
*1
TTYCS-1
*3
24P0077 RJB-TMB
TB12
TB2
1 24:24V
24:24V 1
A:DIG_SIG17 2
2 A:DIG_SIG1
B:DIG_RTN17 3
3 B:DIG_RTN1
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG18 6
6 A:DIG_SIG2
B:DIG_RTN18 7
7 B:DIG_RTN2
G:GND 8
8 G:GND
TB13
TB3
24:24V 1
1 24:24V
A:DIG_SIG19 2
2 A:DIG_SIG3
B:DIG_RTN19 3
3 B:DIG_RTN3
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG20 6
6 A:DIG_SIG4
B:DIG_RTN20 7
7 B:DIG_RTN4
G:GND 8
8 G:GND
TB14
TB4
24:24V 1
1 24:24V
A:DIG_SIG21 2
2 A:DIG_SIG5
B:DIG_RTN21 3
3 B:DIG_RTN5
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG22 6
6 A:DIG_SIG6
B:DIG_RTN22 7
7 B:DIG_RTN6
G:GND 8
8 G:GND
TB15
TB5
24:24V 1
1 24:24V
A:DIG_SIG23 2
2 A:DIG_SIG7
B:DIG_RTN23 3
3 B:DIG_RTN7
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG24 6
6 A:DIG_SIG8
B:DIG_RTN24 7
7 B:DIG_RTN8
G:GND 8
8 G:GND
TB17
TB7
24:24V 1
1 24:24V
A:DIG_SIG25 2
2 A:DIG_SIG9
B:DIG_RTN25 3
3 B:DIG_RTN9
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG26 6
6 A:DIG_SIG10
B:DIG_RTN26 7
7 B:DIG_RTN10
G:GND 8
8 G:GND
TB18
TB8
24:24V 1
1 24:24V
A:DIG_SIG27 2
2 A:DIG_SIG11
B:DIG_RTN27 3
3 B:DIG_RTN11
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG28 6
6 A:DIG_SIG12
B:DIG_RTN28 7
7 B:DIG_RTN12
G:GND 8
8 G:GND
TB9
TB19
1 24:24V
24:24V 1
A:DIG_SIG29 2
2 A:DIG_SIG13
B:DIG_RTN29 3
3 B:DIG_RTN13
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG30 6
6 A:DIG_SIG14
B:DIG_RTN30 7
7 B:DIG_RTN14
8 G:GND
G:GND 8
TB10
TB20
1 24:24V
24:24V 1
A:DIG_SIG31 2
2 A:DIG_SIG15
B:DIG_RTN31 3
3 B:DIG_RTN15
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG32 6
6 A:DIG_SIG16
B:DIG_RTN32 7
7 B:DIG_RTN16
8 G:GND
G:GND 8
*3
*3
*3
*3
*3
*3
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
DIGITAL
(CONTACT)
CH17
DIGITAL
(VOLTAGE)
*1
CH33 TTYCS-1
CH34
*1
TTYCS-1
CH18
CH35
CH19
*1
TTYCS-1
*1
CH36 TTYCS-1
CH20
CH37
CH21
CH38
*1
TTYCS-1
*1
TTYCS-1
CH22
*1
*3
*3
*3
*3
*3
*3
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
CH39 TTYCS-1
CH23
CH40
*1
TTYCS-1
CH24
CH41
CH25
CH42
*1
TTYCS-1
*1
TTYCS-1
CH26
CH43
CH27
CH44
*1
TTYCS-1
*1
TTYCS-1
CH28
*1
*3
*3
*1
TTYCS-1
*1
TTYCS-1
CH45 TTYCS-1
CH29
CH46
*1
TTYCS-1
CH30
*1
*3
*3
4
3
*1
TTYCS-1
*1
TTYCS-1
CH47 TTYCS-1
CH31
CH48
CH32
*1
TTYCS-1
RJB-TMB
TB22
TB32
24P0077
24:24V
24:24V 1
A:DIG_SIG33
A:DIG_SIG49 2
B:DIG_RTN33
B:DIG_RTN49 3
G:GND
G:GND 4
24:24V
24:24V 5
A:DIG_SIG34
A:DIG_SIG50 6
B:DIG_RTN34
B:DIG_RTN50 7
G:GND
G:GND 8
TB23
TB33
24:24V 1
1 24:24V
A:DIG_SIG51 2
2 A:DIG_SIG35
B:DIG_RTN51 3
3 B:DIG_RTN35
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG52 6
6 A:DIG_SIG36
B:DIG_RTN52 7
7 B:DIG_RTN36
G:GND 8
8 G:GND
TB24
TB34
1 24:24V
24V 1
A:DIG_SIG53 2
2 A:DIG_SIG37
B:DIG_RTN53 3
3 B:DIG_RTN37
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG54 6
6 A:DIG_SIG38
B:DIG_RTN54 7
7 B:DIG_RTN38
G:GND 8
8 G:GND
TB25
TB35
24:24V 1
1 24:24V
A:DIG_SIG55 2
2 A:DIG_SIG39
B:DIG_RTN55 3
3 B:DIG_RTN39
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG56 6
6 A:DIG_SIG40
B:DIG_RTN56 7
7 B:DIG_RTN40
G:GND 8
8 G:GND
TB27
TB37
1 24:24V
24:24V 1
A:DIG_SIG57 2
2 A:DIG_SIG41
B:DIG_RTN57 3
3 B:DIG_RTN41
G:GND 4
4 G:GND
24:24V 5
5 24:24V
6 A:DIG_SIG42
A:DIG_SIG58 6
7 B:DIG_RTN42
B:DIG_RTN58 7
8 G:GND
G:GND 8
TB28
TB38
1 24:24V
24:24V 1
A:DIG_SIG59 2
2 A:DIG_SIG43
B:DIG_RTN59 3
3 B:DIG_RTN43
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG60 6
6 A:DIG_SIG44
B:DIG_RTN60 7
7 B:DIG_RTN44
8 G:GND
G:GND 8
TB39
TB29
1 24:24V
24:24V 1
A:DIG_SIG61 2
2 A:DIG_SIG45
B:DIG_RTN61 3
3 B:DIG_RTN45
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG62 6
6 A:DIG_SIG46
B:DIG_RTN62 7
7 B:DIG_RTN46
G:GND 8
8 G:GND
TB30
TB40
1 24:24V
24:24V 1
A:DIG_SIG63 2
2 A:DIG_SIG47
B:DIG_RTN63 3
3 B:DIG_RTN47
G:GND 4
4 G:GND
24:24V 5
5 24:24V
A:DIG_SIG64 6
6 A:DIG_SIG48
B:DIG_RTN64 7
7 B:DIG_RTN48
8 G:GND
G:GND 8
*1
TTYCS-1
1
2
3
4
5
6
7
8
*1
TTYCS-1
*1
TTYCS-1
5
DIGITAL
(VOLTAGE)
SERIAL
IEC61162-1/2
CH49
CONSULT WITH SHIPOWNER AND/OR SHIPYARD ABOUT CONNECTION OF DEVICES.
NOTE
*1: SHIPYARD SUPPLY.
*2: SET JUMPER BETWEEN I AND V FOR 4-20mA SIGNAL.
*3: JUMPER SET BETWEEN 24V AND A-TERMINAL AT FACTORY.
MODIFY SETTING TO CONNECT A VOLTAGE LINE.
CH2
CH50
SERIAL
IEC61162-1
CH3
CH51
CH4
*1
TTYCS-1
*1
TTYCS-1
CH52
CH5
CH6
CH53
CH7
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
CH54
CH8
*1
TTYCS-1Q
*1
TTYCS-1Q
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
TB45
1 A:SER_A1
2 B:SER_B1
3 G:SER_ISOGND1
TB50
1 A:SER_A2
2 B:SER_B2
3 G:SER_ISOGND2
TB11
1 A:SER_A3
2 B:SER_B3
TB16
1 A:SER_A4
2 B:SER_B4
TB21
1 A:SER_A5
2 B:SER_B5
TB26
1 A:SER_A6
2 B:SER_B6
TB31
1 A:SER_A7
2 B:SER_B7
TB36
1 A:SER_A8
2 B:SER_B8
TB6
1 SER_OUT_A
2 SER_OUT_B
3
4
CH55
CH56
CH57
CH58
CH59
CH60
CH61
RJB-TMB
24P0077
CH62
TB41
V:AN_SIG1 1
I:470ohm1 2
G:AN_RTN1 3
V:AN_SIG2 4
I:470ohm2 5
G:AN_RTN2 6
TB42
V:AN_SIG3 1
I:470ohm3 2
G:AN_RTN3 3
V:AN_SIG4 4
I:470ohm4 5
G:AN_RTN4 6
TB43
V:AN_SIG5 1
I:470ohm5 2
G:AN_RTN5 3
V:AN_SIG6 4
I:470ohm6 5
G:AN_RTN6 6
TB44
V:AN_SIG7 1
I:470ohm7 2
G:AN_RTN7 3
V:AN_SIG8 4
I:470ohm8 5
G:AN_RTN8 6
TB46
V:AN_SIG9 1
I:470ohm9 2
G:AN_RTN9 3
V:AN_SIG10 4
I:470ohm10 5
G:AN_RTN10 6
TB47
V:AN_SIG11 1
I:470ohm11 2
G:AN_RTN11 3
V:AN_SIG12 4
I:470ohm12 5
G:AN_RTN12 6
TB48
V:AN_SIG13 1
I:470ohm13 2
G:AN_RTN13 3
V:AN_SIG14 4
I:470ohm14 5
G:AN_RTN14 6
TB49
V:AN_SIG15 1
I:470ohm15 2
G:AN_RTN15 3
V:AN_SIG16 4
I:470ohm16 5
G:AN_RTN16 6
TB1
24V 1
OV 2
J1
TX-P
TX-N
RX-P
CH63
RX-N
*1
TTYCS-1
RJB-MAIN
24P0069
CH64
*1
TTYCS-1
*2
*1
TTYCS-1
ANALOG
CH1
CH2
*2
*1
TTYCS-1
*2
*1
TTYCS-1
CH3
CH4
*2
*1
TTYCS-1
*2
*1
TTYCS-1
CH5
CH6
*2
*1
TTYCS-1
*2
*1
TTYCS-1
CH7
CH8
*2
*1
TTYCS-1
*2
*1
TTYCS-1
CH9
CH10
*2
*1
TTYCS-1
*2
*1
TTYCS-1
CH11
CH12
*2
*1
TTYCS-1
*2
*1
TTYCS-1
CH13
CH14
*2
*1
TTYCS-1
*2
*1
TTYCS-1
CH15
CH16
*2
*1
DPYC-1.5
*1 RJ45
STP(CAT5)
RJ45
1
2
3
4
5
6
7
8
P
P P
P
24VDC
HUB OR DCU
1
2
3
4
5
6
7
8
*1
IV-8sq.
DRAWN
各信号の接続に関しては造船所/船主との事前打合せが必要です。
注記
＊１）造船所手配。
＊２）入力信号が4-20mAの場合はV-I間をショートすること。
＊３）接点信号接続用に24V-A端子間にジャンパー取付済。
電圧信号接続時は設定を変更する。
CH1
S-3
6
18/Jun/2014
CHECKED
18/Jun/2014
APPROVED
T.YAMASAKI
H.MAKI
MASS
kg
DWG No.
C4437-C02- K
IF-8530
名称
接続箱
相互結線図
NAME
JUNCTION BOX
INTERCONNECTION DIAGRAM
VR-7000
VR-3000/3000S
19/Jun/2014 H.MAKI
SCALE
TITLE
REF.No.
TX-P(DA+)
TX-N(DA-)
RX-P(DB+)
RX-N(DB-)
S-4
1
2
3
A
VHFインターフェイス
VHF INTERFACE
IF-5200
*2
FM10PS-6H
ハンドセットハンガー
HANDSET HANGER
HSC701K-B20
マイクレセプタクル
ボックス
MIC RECEPTACLE BOX
RBD-VHF/VHF-B
No.1
B
1
2
3
4
5
6
1
2
3
*1
TTYCY-4S
P
P
4
CN3
0V
PTT SW
MIC-H
MIC-C
SP(H)
THRU1
CN4
0V
PTT SW
MIC-H
MIC-C
SP(H)
THRU1
THRU2
0V
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
CN7/8
CN5
0V
0V
PTT SW PTT SW
MIC-H
MIC-H
MIC-C
MIC-C
SP(H)
SP(H)
THRU1
THRU1
THRU2
THRU2
0V
0V
1
2
3
4
5
6
7
8
CN6
CN9
0V
24VDC(+) 1
PTT SW 24VDC(-) 2
MIC-H
3
MIC-C
OUT1(H) 4
OUT1(L) 5
SP(H)
6
THRU1
OUT2(H) 7
THRU2
OUT2(L) 8
0V
1
2
3
4
5
6
7
8
*2
NH8P
付属ケーブル
ATTACHED CABLE
CC490,1m
*2
NH8P
付属ケーブル
ATTACHED CABLE
CC491,1m
VHF送受信機
VHF TRANSCEIVER UNIT
FM-8500
HANDSET
*2
FM10PS-6H J1105
1 0V
2 PTT SW
3 MIC-H
4 MIC-C
5 HS SP
6 HOOK SW
*2
FM14-7P
1
2
3
4
5
6
7
WING HANDSET
J602
0V
W_PTT SW
W_MIC
W_SP
TX/RX
+15V
0V
ウイングハンドセット
WING HANDSET
*3
HS6000FZ-6/5
マイクレセプタクル
ボックス
MIC RECEPTACLE BOX
RBD-VHF/VHF-B
No.2
1
2
3
*1
TTYCY-4S
P
P
4
C
ウイングハンドセット
WING HANDSET
*3
HS6000FZ-6/5
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
24VDC
VHF-1
L+
LVHF-2
L+
L-
VR-5000
データ収録ユニット
DATA COLLECTING UNIT
VR-5010
TB-12
2 A
3 B
TB-13
2 A
3 B
VR-3000/3000S
データ収録ユニット
DATA COLLECTING UNIT
VR-3010
注記
＊１）造船所手配。
＊２）工場にて取付済み。
＊３）1台のウイングハンドセットを共用する。
D
NOTE
*1. SHIPYARD SUPPLY.
*2. FITTED AT FACTORY.
*3. ONE WING HANDSET IS USED IN COMMON.
DRAWN
MAY 23, '06
CHECKED
APPROVED
SCALE
DWG.No.
TITLE
E.MIYOSHI
TAKAHASHI.T
名称
Y. Hatai
MASS
C4418-C02- J
kg
NAME
IF-5200 (W/FM-8500)
VHFインターフェイス
相互結線図
VHF INTERFACE
INTERCONNECTION DIAGRAM
S-5
1
2
3
VHF送受信機
VHF RADIO
FM-8700
A
VHFインターフェイス
VHF INTERFACE
IF-5200
*2
FM10PS-6H
ハンドセットハンガー
HANDSET HANGER
HSC701K-B20
マイクレセプタクル
ボックス
MIC RECEPTACLE BOX
RBD-VHF/VHF-B
No.1
B
1
2
3
4
5
6
1
2
3
*1
TTYCY-4S
P
P
4
CN3
0V
PTT SW
MIC-H
MIC-C
SP(H)
THRU1
1
2
3
4
5
6
7
8
ウイングハンドセット
WING HANDSET
*3
HS6000FZ-6/5
マイクレセプタクル
ボックス
MIC RECEPTACLE BOX
RBD-VHF/VHF-B
No.2
1
2
3
4
C
*1
TTYCY-4S
P
P
1
2
3
4
5
6
7
8
CN4
0V
PTT SW
MIC-H
MIC-C
SP(H)
THRU1
THRU2
0V
CN5
0V
PTT SW
CN7/8
MIC-H
MIC-C
0V
SP(H) PTT SW
MIC-H
THRU1
MIC-C
THRU2
SP(H)
0V
THRU1
THRU2
0V
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
CN6
CN9
0V
24VDC(+) 1
PTT SW 24VDC(-) 2
MIC-H
3
MIC-C
OUT1(H) 4
OUT1(L) 5
SP(H)
6
THRU1
OUT2(H) 7
THRU2
OUT2(L) 8
0V
ウイングハンドセット
WING HANDSET
*3
HS6000FZ-6/5
*2
NH8P
*2
NH8P
送受信部
TRANSCEIVER UNIT
FM-8700
付属ケーブル
HANDSET
*2
ATTACHED CABLE FM10PS-6H J1105
CC490,1m
1 0V
2 PTT SW
3 MIC-H
4 MIC-C
5 HS SP
6 HOOK SW
付属ケーブル
ATTACHED CABLE
CC491,1m
クロ BLK
ﾐﾄﾞﾘ GRN
アカ RED
アオ BLU
シロ WHT
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
デュプレクサユニット
DUPLEXER UNIT
DX-8700
WING HANDSET
TB201
0V
W_PTT SW
W_MIC
W_SP
F_GND
*4
1
2
3
4
5
24VDC
VHF-1
L+
LVHF-2
L+
L-
VR-5000
データ収録ユニット
DATA COLLECTING UNIT
VR-5010
TB-12
2 A
3 B
TB-13
2 A
3 B
VR-3000/3000S
データ収録ユニット
DATA COLLECTING UNIT
VR-3010
注記
＊１）造船所手配。
＊２）工場にて取付済み。
＊３）1台のウイングハンドセットを共用する。
＊４）コネクタプラグを取り外して結線する。
D
NOTE
*1. SHIPYARD SUPPLY.
*2. FITTED AT FACTORY.
*3. ONE WING HANDSET IS USED IN COMMON.
*4. CONNECT CORES AFTER REMOVE CONNECTOR PLUG.
DRAWN
Jun. 26,'06
CHECKED
APPROVED
SCALE
DWG.No.
TITLE
E.MIYOSHI
TAKAHASHI.T
名称
Y.Hatai
MASS
C4418-C03- K
kg
NAME
IF-5200 (W/FM-8700)
VHFインターフェイス
相互結線図
VHF INTERFACE
INTERCONNECTION DIAGRAM
S-6
1
2
3
レーダー映像自動切換器
RADAR VIDEO SWITCH INTERFACE
IF-1000RVC
A
100-230VAC
1φ,50-60Hz
RADAR 1
RADAR 2
OUT1 BNC
*1
DPYC-1.5
TB1
1 L
2 N
J9
BNC
J10
BNC
J11
BNC
J12
BNC
J13
BNC
OUT2 BNC
J14
R
BNC
J15
BNC
J16
BNC
J17
BNC
J18
BNC
R
*3
G
*1
TTYCS-1
*1
TTYCS-1
1
2
3
4
TB2
TRG1
GND
TRG2
GND
B
H
RADAR 1
B
Dsub15P
IN1
KB-HD152K,2m
*2
J5
3COX-2P-6C,5/10m,φ8.5 (mini)
R
1
OR VGA CABLE *1
GND
6
G
2
GND
7
B
3
GND
8
NC
4
NC
9
NC
5
GND
10
H
13
GND
11
V
14
NC
12
15
NC
V
G
B
H
V
RADAR 2
Dsub15P
KB-HD152K,2m
*2
3COX-2P-6C,5/10m,φ8.5 (mini)
OR VGA CABLE *1
J6
IN2
OUT1
J7
同上
DITTO
OUT2
C
J8
*2
1.5C2V-3C2V-T-20M/30M,
VDR/S-VDR
20/30m,φ21
OR COAX.CABLE(x5) *1
*2
1.5C2V-3C2V-T-20M/30M,
VDR/S-VDR
20/30m,φ21
OR COAX.CABLE(x5) *1
Dsub15P
(mini)
KB-HD152K,2m *2
3COX-2P-6C,5/10m,φ8.5
OR VGA CABLE *1
VDR/S-VDR
Dsub15P
(mini)
KB-HD152K,2m *2
3COX-2P-6C,5/10m,φ8.5
OR VGA CABLE *1
VDR/S-VDR
PE *1
IV-2sq.
D
注記
＊１）造船所手配。
＊２）オプション。
＊３）出力はBNCまたはDsubのいずれかを選択。（内部設定）
NOTE
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: SELECT BNC OR D-SUB OUTPUT.(MODIFY INNER SETTING)
DRAWN
CHECKED
APPROVED
SCALE
DWG.No.
8/May/08
8/May/08
TITLE
T.YAMASAKI
名称
T.TAKENO
16/May/08 R.Esumi VR-5000/3000
MASS
C4418-C06- A
NAME
kg
REF.No.
24-009-5050-0
IF-1000RVC
レーダー映像自動切換器
相互結線図
RADAR VIDEO SWITCH INTERFACE
INTERCONNECTION DIAGRAM