Nov 10, 2014 - KYOCERA Display

Spec No.
Date
SPEC
TQ3C-8EAF0-E1YAA103-01
September 24, 2014
TYPE : TCG070WVLPEAFA-AA30
< 7.0 inch WVGA transmissive color TFT with LED backlight
and constant current circuit for LED backlight and touch panel>
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Application
Construction and outline
Mechanical specifications
Absolute maximum ratings
Electrical characteristics
Optical characteristics
Interface signals
Input timing characteristics
Design guidance for analog touch panel
Lot number identification
Warranty
Precautions for use
Reliability test data
Outline drawing
Nov 10, 2014
KYOCERA DISPLAY CORPORATION
This specification is subject to change without notice.
Consult Kyocera before ordering.
Original
Issue Date
December 20, 2012
Designed by: Engineering dept.
Prepared
Checked
Confirmed by: QA dept.
Approved
Checked
Approved
Spec No.
TQ3C-8EAF0-E1YAA103-01
Part No.
Page
TCG070WVLPEAFA-AA30
Warning
1. This Kyocera LCD module has been specifically designed for use only in
electronic devices and industrial machines in the area of audio control,
office automation, industrial control, home appliances, etc. The module
should not be used in applications where the highest level of safety and
reliability are required and module failure or malfunction of such module
results in physical harm or loss of life, as well as enormous damage or loss.
Such fields of applications include, without limitation, medical, aerospace,
communications infrastructure, atomic energy control. Kyocera expressly
disclaims any and all liability resulting in any way to the use of the module
in such applications.
2. Customer agrees to indemnify, defend and hold Kyocera harmless
from and against any and all actions, claims, damages, liabilities,
awards, costs, and expenses, including legal expenses, resulting from or
arising out of Customer's use, or sale for use, or Kyocera modules in
applications.
Caution
1. Kyocera shall have the right, which Customer hereby acknowledges, to
immediately scrap or destroy tooling for Kyocera modules for which no
Purchase Orders have been received from the Customer in a two-year period.
-
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Revision record
Designed by : Engineering dept.
Prepared
Checked
Approved
Date
TCG070WVLPEAFA-AA30
Confirmed by : QA dept.
Checked
Approved
September 24, 2014
Rev.No.
Date
Page
01
Sep 24, 2014
㸫
5
Descriptions
Change KYOCERA CORPORATION LCD DIVISION
ЍKYOCERA DISPLAY CORPORATION
5-2. Constant current circuit for LED Backlight
change Operating life time Typ70,000h Ѝ100,000㹦
Page
-
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
1
1. Application
This document defines the specification of TCG070WVLPEAFA-AA30.
(RoHS Compliant)
2. Construction and outline
: Transmissive color dot matrix type TFT
: LED
: Anti-Glare treatment
: LVDS
: Timing controller, Power supply (3.3V input)
With Constant current circuit for LED Backlight(12V input)
: Analog type, Non-Glare treatment
LCD
Backlight system
Polarizer
Interface
Additional circuit
Touch panel
3. Mechanical specifications
3-1. LCD
Item
Specification
Unit
Outline dimensions 1)
165(W)×(104.4)(H)×10.4(D)
mm
Active area
152.4(W)×91.44(H)
(17.8cm/7.0 inch(Diagonal))
mm
Dot format
800×(R,G,B)(W)×480(H)
dot
0.0635(W)×0.1905(H)
mm
Normally White
-
265
g
Dot pitch
Base color
2)
Mass
1) Projection not included. Please refer to outline for details.
2) Due to the characteristics of the LCD material, the color varies with environmental temperature.
3-2. Touch panel
Item
Specification
Unit
Radius-0.8 stylus or Finger
-
Actuation Force
0.05㹼0.8
N
Transmittance
Typ. 80
%
Pencil hardness 2H or more according
-
None
-
Input
Surface hardness
Anti newton’s ring treatment
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
2
4. Absolute maximum ratings
4-1. Electrical absolute maximum ratings
Item
Symbol
Min.
Max.
Unit
Supply voltage(+3.3V)
VDD
-0.3
4.0
V
Supply voltage(+12V)
VIN
-0.3
14.0
V
VI1
-0.3
2.8
V
CK IN+, CK IN-
VI2
-0.3
2.8
V
SELLVDS, BITSEL, SC
VI3
-0.3
VDD+0.5
V
BLBRT, BLEN
VI4
-0.3
VIN
V
Supply voltage for touch panel
VTP
0
6.0
V
Input current of touch panel
ITP
0
0.5
mA
RxINi+, RxINiInput signal
voltage 2)
1)
1) i=0,1,2,3
2) VDD must be supplied correctly within the range described in 5-1.
4-2. Environmental absolute maximum ratings
Item
Symbol
Min.
Max.
Unit
Operating temperature
1)
TOP
-20
70
°C
Storage temperature
2)
TSTO
-30
80
°C
Operating humidity
3)
HOP
10
4)
%RH
Storage humidity
3)
HSTO
10
4)
%RH
Vibration
-
5)
5)
-
Shock
-
6)
6)
-
1) Operating temperature means a temperature which operation shall be guaranteed. Since display
performance is evaluated at 25°C, another temperature range should be confirmed.
2) Temp. = -30°C㸺48h , Temp. = 80°C㸺168h
Store LCD at normal temperature/humidity. Keep them free from vibration and shock.
An LCD that is kept at a low or a high temperature for a long time can be defective due to
other conditions, even if the low or high temperature satisfies the standard.
(Please refer to “Precautions for Use” for details.)
3)
4)
5)
Non-condensing
Temp.ӌ40°C, 85%RH Max.
Temp.㸼40°C, Absolute humidity shall be less than 85%RH at 40°C.
Frequency
10㹼55 Hz
Vibration width
0.15mm
Interval
10-55-10 Hz
Acceleration value
(0.3㹼9 m/s2)
㸯minutes
2 hours in each direction X, Y, Z (6 hours total)
EIAJ ED-2531
6) Acceleration: 490 m/s2, Pulse width: 11 ms
3 times in each direction: ±X, ±Y, ±Z
EIAJ ED-2531
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
3
TCG070WVLPEAFA-AA30
5. Electrical characteristics
5-1. LCD
Item
Temp. = -20㹼70°C
Symbol
Condition
Min.
Typ.
Max.
Unit
VDD
-
3.0
3.3
3.6
V
Current consumption
IDD
2)
-
200
260
mA
Permissive input ripple voltage
VRP
VDD=3.3V
-
-
100
mVp-p
VIL
"Low" level
0
-
0.8
V
VIH
"High" level
2.0
-
VDD
V
IOL
VI3=0V
-10
-
10
ȣA
IOH
VI3=3.3V
-
-
400
ȣA
Supply voltage
Input signal voltage
1)
3)
Input reek current
LVDS Input voltage
4)
VL
-
0
-
1.9
V
Differential input voltage
4)
VID
-
250
350
450
mV
Differential input
threshold voltage
4) 5)
VTL
"Low" level
VCM-100
-
-
mV
VTH
"High" level
-
-
VCM+100
mV
R1
-
-
100
-
Ȑ
t1
-
0.1
-
10
ms
t2
-
0
-
-
ms
t3
-
0
-
-
ms
t4
-
1.0
-
-
s
t5
-
200
-
-
ms
t6
-
200
-
-
ms
t7
-
0
-
10
s
t8
-
0
-
-
ms
Terminator
VDD-turn-on conditions
1)
1) VDD-turn-on conditions
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
TCG070WVLPEAFA-AA30
2) Display pattern:
VDD = 3.3V, Temp. = 25°C
123 456
1
2
3
:
:
:
479
480
(dot)
࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭࣭2398 2399 2400(dot)
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
‫ڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦڦ‬
3) Input signal : SELLVDS, BITSEL, SC
4) Input signal : RxIN3+, RxIN3-, RxIN2+, RxIN2-, RxIN1+, RxIN1-, RxIN0+, RxIN0CK IN+, CK IN-
㼂㻵㻰
㼂㻸
㼂㻯㻹
㻜㼂
5) VCM : LVDS Common mode voltage (VCM=1.25V)
6) Please power on LVDS transmitter at the same time as VDD, or LVDS transmitter should be
powered on first.
M407011 Page
4
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
5
5-2. Constant current circuit for LED Backlight
Temp. = -20㹼70°C
Item
Supply voltage
1)
Current consumption
Permissive input ripple voltage
BLBRT Input signal voltage
BLBRT Input pull-down resistance
BLEN Input signal voltage
BLEN Input pull-down resistance
㹎㹕㹋 Frequency
3)
㹎㹕M Duty ratio
3)
Operating life time
1)
4), 5)
Symbol
Condition
Min.
Typ.
Max.
Unit
VIN
-
10.8
12.0
13.2
V
IIN
2)
-
235
400
mA
VRP_BL
VIN=12.0V
-
-
100
mVp-p
VIL_BLBRT
"Low" level
0
-
0.8
V
VIH_BLBRT
"High" level
2.3
-
VIN
V
RIN_BLBRT
-
100
300
500
kȐ
VIL_BLEN
"Low" level
0
-
0.8
V
VIH_BLEN
"High" level
2.3
-
VIN
V
RIN_BLEN
-
100
300
500
kȐ
fPWM
-
200
-
10k
Hz
fPWM=200Hz
1
-
100
%
fPWM=2kHz
10
-
100
%
fPWM=10kHz
50
-
100
%
Temp.=25°C
-
100,000
-
h
DPWM
T
VIN-turn-on conditions
㻜㻚㻥㼂㻵㻺
㼂㻵㻺
㻜㻚㻝㼂㻵㻺
㻜㼙㼟
㻔㼙㼕㼚㻕
㻮㻸㻱㻺
㻜㼙㼟
㻔㼙㼕㼚㻕
㻜㼙㼟
㻔㼙㼕㼚㻕
㻼㼃㻹 㼟㼕㼓㼚㼍㼘
㻜㼙㼟
㻔㼙㼕㼚㻕
㻮㻸㻮㻾㼀
㻌㻌㻌㻌㻌㻌㻌㻌㻭㼒㼠㼑㼞㻌㼟㼕㼓㼚㼍㼘㻌㼕㼟㻌㼕㼚㼜㼡㼠㻘㻌㼕㼠㻌㼣㼕㼘㼘㻌㼠㼍㼗㼑㻌㻞㻜㻜㼙㼟㻔㻹㼕㼚㻚㻕㻌㼠㼛㻌㼟㼠㼍㼎㼕㼘㼕㼦㼑㻌
㻌㻌㻌㻌㻌㻌㻌㻌㼜㼛㼣㼑㼞㻌㼛㼒㻌㼎㼍㼏㼗㼘㼕㼓㼔㼠㻚㻌
㻌㻌㻌㻌㻌㻌㻌㻌㻹㼑㼍㼚㼣㼔㼕㼘㼑㻘㻌㼠㼛㼚㻌㼛㼒㻌㻮㻸㻮㻾㼀㻌㼟㼔㼛㼡㼘㼐㻌㼎㼑㻌㼙㼛㼞㼑㻌㼠㼔㼍㼚㻌㻞㻜㻜䃛㼟㻚
㻞㻜㻜㼙㼟
㻔㼙㼕㼚㻕
㻻㻺
㻸㻱㻰
㻮㼍㼏㼗㼘㼕㼓㼔㼠
㻻㻲㻲
㻻㻲㻲
2) VIN = 12V, Temp. = 25Υ㸪DPWM = 100%
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
3) PWM Timing Diagram
tON㸪tOFF Ӎ 50ȣs.
In case of lower frequency, the deterioration of the display quality, flicker etc., may occur.
4) When brightness decrease 50% of minimum brightness.
㻌 㻌 㻌 The average life of a LED will decrease when the LCD is operating at higher temperatures.
5) Life time is estimated data. (Condition : IF=60mA, Ta=25Υ in chamber).
5-3. Touch panel
Item
Supply voltage for touch panel
Terminal resistance
Linearity
Insulation resistance
Specification
5.0V
xL㹼xR : 274Ȑ㹼640ƺ
yU㹼yL : 183ƺ㹼428ƺ
less than ±2.0%
1000ƺRUPRUHDW'&9
M407011 6
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
7
TCG070WVLPEAFA-AA30
6. Optical characteristics
Item
Response time
Measuring spot =ȭ6.0mm, Temp. = 25°C
Symbol
Condition
Min.
Typ.
Max.
Unit
Rise
Ǖr
ȟ=ȭ=0°
-
5
-
ms
Down
Ǖd
ȟ=ȭ=0°
-
25
-
ms
ȟUPPER
-
60
-
ȟLOWER
-
80
-
-
80
-
-
80
-
Viewing angle range
View direction
: 12 o’clock
(Gray inversion)
CRӍ10
ȭLEFT
䃥RIGHT
Contrast ratio
Brightness
ȟ=ȭ=0°
700
1000
-
-
L
IF=60mA/Line
390
560
-
cd/m2
0.550
0.600
0.650
0.300
0.350
0.400
0.270
0.320
0.370
0.500
0.550
0.600
0.100
0.150
0.200
0.070
0.120
0.170
0.240
0.290
0.340
0.255
0.305
0.355
y
x
Green
y
Chromaticity
coordinates
x
Blue
y
x
White
y
ȟ=ȭ=0°
ȟ=ȭ=0°
ȟ=ȭ=0°
ȟ=ȭ=0°
6-1. Definition of contrast ratio
CR(Contrast ratio) 㸻
Brightness with all pixels "White"
Brightness with all pixels "Black"
6-2. Definition of response time
:KLWH
%ODFN
%ULJKWQHVV
:KLWH
ȫU
deg.
CR
x
Red
deg.
ȫG
M407011 -
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
8
TCG070WVLPEAFA-AA30
6-3. Definition of viewing angle
ȭ r
ȟ833(5
\
ȟ r
\
ȟ/2:(5
ȭ/()7
[
[
ȭ5,*+7
[
[
\
\
ȭGLUHFWLRQ
ȟGLUHFWLRQ
6-4. Brightness measuring points
200×3
120
1
600×3
(dot)
4
3
240
360
400×3
2
5
(dot)
1) Rating is defined as the white brightness at center of display screen(3).
2) 5 minutes after LED is turned on. (Ambient Temp.=25Υ)
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
9
TCG070WVLPEAFA-AA30
7. Interface signals
7-1. Interface signals
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Symbol
BITSEL
SELLVDS
GND
GND
RxIN3+
RxIN3GND
CK IN+
CK INGND
RxIN2+
RxIN2GND
RxIN1+
RxIN1GND
RxIN0+
RxIN0GND
GND
VDD
VDD
SC
BLBRT
BLEN
NC
VIN
VIN
GNDB
GNDB
LCD connector
Matching connector
Description
Bit data select signal(GND or Open: 8bit modeࠊHigh: 6bit mode)
Mode select signal(LVDS Data mapping)
GND
GND
LVDS receiver signal CH3(+)
LVDS receiver signal CH3(-)
GND
LVDS receiver signal CK(+)
LVDS receiver signal CK(-)
GND
LVDS receiver signal CH2(+)
LVDS receiver signal CH2(-)
GND
LVDS receiver signal CH1(+)
LVDS receiver signal CH1(-)
GND
LVDS receiver signal CH0(+)
LVDS receiver signal CH0(-)
GND
GND
+3.3V power supply
+3.3V power supply
Scan direction control(High or Open: NormalࠊGND: Reverse)
PWM signal(Brightness adjustment)
ON/OFF terminal voltage
NC
+12V power supply
+12V power supply
GND (Backlight)
GND (Backlight)
㸸 MDF76GW-30S-1H(55)
㸸 MDF76-30P-1C
(HIROSE)
(HIROSE)
LVDS receiver
㸸 Embedded in ASIC
Matching LVDS transmitter 㸸 THC63LVDM83R(THine Electronics) or compatible
1) Scanning
SC : High or Open
SC : GND
M407011 Note
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
1)
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
7-2. Data mapping (6bit input / 8bit mode)
1) Location of BITSEL, SELLVDS (THC63LVDM83R(THine Electronics) or compatible)
Transmitter
1Pin BITSEL
= "L" or OPEN 1Pin BITSEL
= "L" or OPEN
2Pin SELLVDS = "L" or OPEN 2Pin SELLVDS = "H"
Pin No.
Data
㸫
R0(LSB)
51
TA0
TA1
㸫
R1
52
TA2
㸫
R2
54
TA3
㸫
R3
55
TA4
㸫
R4
56
TA5
㸫
3
R5(MSB)
TA6
㸫
G0(LSB)
4
㸫
G1
6
TB0
TB1
㸫
G2
7
TB2
㸫
G3
11
TB3
㸫
G4
12
TB4
㸫
14
G5(MSB)
TB5
㸫
B0(LSB)
15
TB6
㸫
B1
19
㸫
B2
20
TC0
TC1
㸫
B3
22
TC2
㸫
B4
23
TC3
㸫
24
B5(MSB)
TC4
㸫
(HS)
27
TC5
㸫
(VS)
28
TC6
㸫
DE
30
㸫
GND
50
TD0
TD1
㸫
GND
2
TD2
GND
㸫
8
TD3
GND
㸫
10
TD4
GND
㸫
16
TD5
GND
㸫
18
TD6
㸫
25
GND
BITSEL=L(GND) or OPEN
SELLVDS=H(3.3V)
1 CYCLE
R1
G0
R5
R4
R3
R2
R1
R0
G0
G1
B1
B0
G5
G4
G3
G2
G1
B1
B2
DE
(VS)
(HS)
B5
B4
B3
B2
DE
DE㸸DATA ENABLE
HS㸸HSYNC
VS㸸VSYNC
M407011 10
Spec No.
TQ3C-8EAF0-E1YAA103-01
Part No.
TCG070WVLPEAFA-AA30
2) Block Diagram
BITSEL=L(GND) or OPEN
SELLVDS=H(3.3V)
ͤSELLVDS signal line has 10㹩Ȑ pulldown resister.
M407011 Page
11
Spec No.
TQ3C-8EAF0-E1YAA103-01
Part No.
TCG070WVLPEAFA-AA30
Page
12
When using ͆6-bit Transmitter͇, please connect the unused channel of the control IC receiver
as described in the diagram below.
ͤSELLVDS signal line has 10㹩Ȑ pulldown resister.
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
7-3. Data mapping (8bit input / 8bit mode)
1) Location of BITSEL, SELLVDS (THC63LVDM83R(THine Electronics) or compatible)
Transmitter
1Pin BITSEL
= "L" or OPEN 1Pin BITSEL
= "L" or OPEN
2Pin SELLVDS = "L" or OPEN 2Pin SELLVDS = "H"
Pin No.
Data
R0(LSB)
R2
51
TA0
TA1
R1
R3
52
TA2
R2
R4
54
TA3
R3
R5
55
TA4
R4
R6
56
TA5
R5
3
R7(MSB)
TA6
G0(LSB)
G2
4
G1
G3
6
TB0
TB1
G2
G4
7
TB2
G3
G5
11
TB3
G4
G6
12
TB4
G5
14
G7(MSB)
TB5
B0(LSB)
B2
15
TB6
B1
B3
19
B2
B4
20
TC0
TC1
B3
B5
22
TC2
B4
B6
23
TC3
B5
24
B7(MSB)
TC4
(HS)
(HS)
27
TC5
(VS)
(VS)
28
TC6
DE
DE
30
R6
R0(LSB)
50
TD0
TD1
R7(MSB)
R1
2
TD2
G6
G0(LSB)
8
TD3
G7(MSB)
G1
10
TD4
B6
B0(LSB)
16
TD5
B7(MSB)
B1
18
TD6
(NA)
25
(NA)
BITSEL=L(GND) or OPEN
SELLVDS=L(GND) or OPEN
1 CYCLE
R1
R0
G0
R5
R4
R3
R2
R1
R0
G0
G2
G1
B1
B0
G5
G4
G3
G2
G1
B1
B3
B2
DE
(VS)
(HS)
B5
B4
B3
B2
DE
㻾㻣
㻾㻢
㻺㻭
㻮㻣
㻮㻢
㻳㻣
㻳㻢
㻾㻣
㻾㻢
㻺㻭
DE㸸DATA ENABLE
HS㸸HSYNC
VS㸸VSYNC
M407011 13
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
TCG070WVLPEAFA-AA30
BITSEL=L(GND) or OPEN
SELLVDS=H(3.3V)
1 CYCLE
R3
R2
G2
R7
R6
R5
R4
R3
R2
G2
G4
G3
B3
B2
G7
G6
G5
G4
G3
B3
B5
B4
DE
(VS)
(HS)
B7
B6
B5
B4
DE
㻾㻝
㻾㻜
㻺㻭
㻮㻝
㻮㻜
㻳㻝
㻳㻜
㻾㻝
㻾㻜
㻺㻭
DE㸸DATA ENABLE
HS㸸HSYNC
VS㸸VSYNC
2) Block Diagram
BITSEL=L(GND) or OPEN
SELLVDS=L(GND) or OPEN
ͤSELLVDS signal line has 10㹩Ȑ pulldown resister.
M407011 Page
14
Spec No.
TQ3C-8EAF0-E1YAA103-01
Part No.
TCG070WVLPEAFA-AA30
BITSEL=L(GND) or OPEN
SELLVDS=H(3.3V)
ͤSELLVDS signal line has 10㹩Ȑ pulldown resister.
M407011 Page
15
Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
TCG070WVLPEAFA-AA30
7-4. Data mapping (6bit input / 6bit mode)
1) Location of BITSEL, SELLVDS (THC63LVDM83R(THine Electronics) or compatible)
Transmitter
1Pin BITSEL
= "H"
1Pin BITSEL
= "H"
2Pin SELLVDS = "L" or OPEN 2Pin SELLVDS = "H"
Pin No.
Data
㸫
R0(LSB)
44
TA0
TA1
㸫
R1
45
TA2
㸫
R2
47
TA3
㸫
R3
48
TA4
㸫
R4
1
TA5
㸫
3
R5(MSB)
TA6
㸫
G0(LSB)
4
㸫
G1
6
TB0
TB1
㸫
G2
7
TB2
㸫
G3
9
TB3
㸫
G4
10
TB4
㸫
12
G5(MSB)
TB5
㸫
B0(LSB)
13
TB6
㸫
B1
15
㸫
B2
16
TC0
TC1
㸫
B3
18
TC2
㸫
B4
19
TC3
㸫
20
B5(MSB)
TC4
㸫
(HS)
22
TC5
㸫
(VS)
23
TC6
㸫
DE
25
BITSEL=H(3.3V)
SELLVDS=L(GND) or OPEN
1 CYCLE
R1
R0
G0
R5
R4
R3
R2
R1
R0
G0
G2
G1
B1
B0
G5
G4
G3
G2
G1
B1
B3
B2
DE
(VS)
(HS)
B5
B4
B3
B2
DE
㻾㻣
㻾㻢
㻺㻭
㻮㻣
㻮㻢
㻳㻣
㻳㻢
㻾㻣
㻾㻢
㻺㻭
DE㸸DATA ENABLE
HS㸸HSYNC
VS㸸VSYNC
M407011 Page
16
Spec No.
TQ3C-8EAF0-E1YAA103-01
Part No.
TCG070WVLPEAFA-AA30
Page
17
2) Block Diagram
BITSEL=H(3.3V)
SELLVDS=L(GND) or OPEN
ͤSELLVDS signal line has 10㹩Ȑ pulldown resister.
7-5. Touch panel
No.
Symbol
Description
1
xR
x-Right terminal
2
yL
y-Lower terminal
3
xL
x-Left terminal
4
yU
y-Upper terminal
Touch panel side connector
Recommended matching connector
㸸 1mm pitch
㸸 08 6262 004 940 846+ (KYOCERA Connector Products)
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
18
TCG070WVLPEAFA-AA30
8. Input timing characteristics
8-1. Timing characteristics
Item
Clock (CK)
Enable signal
(DE)
Refresh rate
Frequency
Symbol
Min.
Typ.
Max.
Unit
1/Tc
29.88
33.2
36.52
MHz
1024
1056
1088
Tc
-
31.8
-
ȣs
Horizontal Period
Th
Horizontal display period
Thd
Vertical Period
Tv
Vertical display period
Tvd
fv
800
487
525
1)
Tc
550
480
50
Note
60
Th
Th
70
Hz
1) Please set a clock frequency, a vertical dormant period, and the horizontal dormant period
so that the Horizontal Period should not reach less than Min. value.
2) If the refresh rate reach less than Min. value, the deterioration of the display quality, flicker etc.,
may occur.(fv=1/Tv)
M407011 2)
Spec No.
TQ3C-8EAF0-E1YAA103-01
Part No.
TCG070WVLPEAFA-AA30
Page
19
8-2. Input Data Signals and Display position on the screen
9. Design guidance for analog touch panel
9-1. Electrical (In customer's design, please remember the following considerations.)
1) Do not use the current regulated circuit.
2) Keep the current limit with top and bottom layer. (Please refer to “Electrical absolute
maximum ratings” for details.)
3) Analog touch panel can not sense two points touching separately.
4) A contact resistance is appeared at the touch point between top and bottom layer. After this
resistance has stable read of the touch panel position data.
5) Because noise of inverter or peripheral circuits may interfere signal of touch panel itself it is
necessary to design carefully in advance to avoid these noise problem.
9-2. Software
1) Do the "User Calibration".
2) "User Calibration" may be needed with long term using. Include "User Calibration" menu in
your software.
3) When drawing a line with a stylus, there may be a slight discontinuity when the stylus passes
over a spacer-dot. If necessary, please provide a compensation feature within your software.
9-3. Mounting on display and housing bezel
1) Do not use an adhesive tape to bond it on the front of touch panel and hang it to the housing
bezel.
2) Never expand the touch panel top layer (PET-film) like a balloon by internal air pressure.
The life of the touch panel will be extremely short.
3) If a dew will be on the heat-sealed area or exposed traces at the end of a flexible tail,
the migration of silver can occur. This will cause sometimes a short circuit.
4) Must maintain a gap between inside of bezel and touch panel to avoid malfunction or electrode
damage of touch panel.
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
20
10. Lot number identification
The lot number shall be indicated on the back of the backlight case of each LCD.
TCG070WVLPEAFA-AA30
-
ŌŌ - ŌŌ - Ō
ŅŅ
12
Ņ
3
MADE IN
Ņ
4
ŌŌŌŌŌ
Ņ
5
No1. - No5. above indicate
1. Year code
2. Month code
3. Date
4. Version Number
5. Country of origin (Japan or China)
Year
2012
2013
2014
2015
2016
2017
Code
2
3
4
5
6
7
Month
Jan.
Feb.
Mar.
Apr.
May
Jun.
Code
1
2
3
4
5
6
Month
Jul.
Aug.
Sep.
Oct.
Nov.
Dec.
Code
7
8
9
X
Y
Z
11. Warranty
11-1. Incoming inspection
Please inspect the LCD within one month after your receipt.
11-2. Production warranty
Kyocera warrants its LCD’s for a period of 12 months from the ship date. Kyocera shall, by mutual
agreement, replace or re-work defective LCD’s that are shown to be Kyocera’s responsibility.
M407011 Spec No.
TQ3C-8EAF0-E1YAA103-01
Part No.
Page
TCG070WVLPEAFA-AA30
21
12. Precautions for use
12-1. Installation of the LCD
1) The LCD shall be installed so that there is no pressure on the LSI chips.
2) The LCD shall be installed flat, without twisting or bending.
3) Please design the housing window so that its edges are between the active area and the effective㻌
area of the LCD screen.
12-2. Static electricity
1) Since CMOS ICs are mounted directly onto the LCD glass, protection from static electricity is
required.
2) Workers should use body grounding. Operator should wear ground straps.
12-3. LCD operation
1) The LCD shall be operated within the limits specified. Operation at values outside of these limits
may shorten life, and/or harm display images.
2) Please select the best display pattern based on your evaluation because flicker, lines or
nonuniformity or unevenness can be visible depending on display patterns.
12-4. Storage
1) The LCD shall be stored within the temperature and humidity limits specified.
Store in a dark area, and protect the LCD from direct sunlight or fluorescent light.
2) Always store the LCD so that it is free from external pressure onto it.
12-5. Usage
1) DO NOT store in a high humidity environment for extended periods. Polarizer degradation bubbles,
and/or peeling off of the polarizer may result.
2) Do not push or rub the touch panel's surface with hard to sharp objects such as knives, or
the touch panel may be scratched.
3) When the touch panel is dirty, gently wipe the surface with a soft cloth, sometimes
moistened by mild detergent or alcohol. If a hazardous chemical is dropped on the touch
panel by mistake, wipe it off right away to prevent human contact.
4) Touch panel edges are sharp. Handle the touch panel with enough care to prevent cuts.
5) Always keep the LCD free from condensation during testing. Condensation may permanently spot
or stain the polarizer.
6) Do not disassemble LCD because it will result in damage.
7) This Kyocera LCD has been specifically designed for use in general electronic devices, but not for
use in a special environment such as usage in an active gas. Hence, when the LCD is supposed to
be used in a special environment, evaluate the LCD thoroughly beforehand and do not expose the
LCD to chemicals such as an active gas.
8) Please do not use solid-base image pattern for long hours because a temporary afterimage may
appear. We recommend using screen saver etc. in cases where a solid-base image pattern must be
used.
9) Liquid crystal may leak when the LCD is broken. Be careful not to let the fluid go into your eyes
and mouth. In the case the fluid touches your body; rinse it off right away with water and soap.
M407011 Spec No.
Part No.
TQ3C-8EAF0-E1YAA103-01
Page
TCG070WVLPEAFA-AA30
13. Reliability test data
Test item
Test condition
Test time
High temp.
atmosphere
80°C
240h
Low temp.
atmosphere
-30°C
240h
High temp.
humidity
atmosphere
40°C 90% RH
240h
Temp. cycle
-30°C 0.5h
R.T. 0.5h
80°C 0.5h
10cycles
High temp.
operation
70°C
500h
Point
Activation
life
Silicon rubber,
Tip : R = 4.0
Hitting force 3N
Hitting speed
2 time/s
one
million
times
1)
2)
3)
4)
Judgement
Display function
Display quality
Current consumption
Display function
Display quality
Current consumption
Display function
Display quality
Current consumption
Display function
Display quality
Current consumption
Display function
Display quality
Current consumption
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
: No defect
Terminal resistance
Insulation resistance
Linearity
Actuation Force
: No defect
: No defect
: No defect
: No defect
Each test item uses a test LCD only once. The tested LCD is not used in any other tests.
The LCD is tested in circumstances in which there is no condensation.
The reliability test is not an out-going inspection.
The result of the reliability test is for your reference purpose only.
The reliability test is conducted only to examine the LCD's capability.
M407011 22
Spec No.
Date
TQ3C-8EAF0-E2YAA103-01
September 24, 2014
KYOCERA INSPECTION STANDARD
TYPE : TCG070WVLPEAFA-AA30
KYOCERA DISPLAY CORPORATION
Original
Issue Date
Designed by : Engineering dept.
Prepared
Checked
Approved
Confirmed by : QA dept.
Checked
Approved
December 20, 2012
Spec No.
Part No.
TQ3C-8EAF0-E2YAA103-01
Date
Revision record
Designed by : Engineering dept.
Prepared
Checked
Approved
Page
TCG070WVLPEAFA-AA30
Confirmed by : QA dept.
Checked
Approved
September 24, 2014
Rev.No.
01
Date
Sep 24, 2014
Page
Descriptions
Change KYOCERA CORPORATION LCD DIVISION
㸫
1
ЍKYOCERA DISPLAY CORPORATION
Change “Definition of inspection item”, Bright dot defect
-
ရྡ
᳨ᰝᇶ‽᭩ 1R
74&($)(<$$
࣮࣌ࢪ
7&*:9/3($11$1
㸧 つ᱁
㐺⏝
グ ஦
ᮏ᳨ᰝᇶ‽᭩࡟グ㍕ࡢ࡞࠸୙ලྜࡀ⏕ࡌࡓሙྜࡣࠊู㏵୧⪅༠㆟ࡢୖỴᐃࡍࡿࡇ࡜࡜ࡋࡲࡍࠋ
ᮏ᳨ᰝᇶ‽ࡣ᭷ຠ⾲♧㡿ᇦ࡟᪊࠸࡚ࡢࡳ㐺⏝ࡍࡿࡶࡢ࡜ࡋࠊ᭷ຠ⾲♧㡿ᇦ௨እࡣ
↓どࡍࡿࡶࡢ࡜ࡋࡲࡍࠋ
᮲௳
↷ᗘ㸦⎔ቃ㸧 /X[PLQ
ࢧࣥࣉࣝࡲ࡛ࡢ㊥㞳PP
ᗘ sΥ
᳨ᰝ᪉ྥ ┿ୖ᪉ྥ
᳨ᰝ㡯┠ࡢᐃ⩏
ⅬḞ㝗
㍤Ⅼ
඲㯮⾲♧⏬㠃࡟࠾࠸࡚ࠊ࿘㎶ྠⰍ⏬⣲ࡼࡾ᫂
ࡿ࠸࡜ㄆ㆑ࡉࢀࡿⅬḞ㝗ࠋ
࣭㸣1'㺪㺆㺷㺞㺎࡛ぢ࠼ࡿ㺸㺫㺼㺷 ͐㍤Ⅼ
࣭㸣1'㺪㺆㺷㺞㺎࡛ぢ࠼࡞࠸㺸㺫㺼㺷͐↓ど
㸺⏬⣲ᣑ኱ཧ⪃ᅗ㸼
⏬⣲ࡢ୰ኸ࡟㟁ᴟࡀ
࠶ࡾࡲࡍࠋ
㯮Ⅼ㸦෇≧ࡢ≀ྵࡴ㸧 ඲ⓑ⾲♧⏬㠃࡟࠾࠸࡚ࠊ࿘㎶ྠⰍ⏬⣲ࡼࡾᬯ
࠸࡜ㄆ㆑ࡉࢀࡿⅬḞ㝗ࠋ
࣭㺙㺐㺛㺼࡟ࡘ࠸࡚ࡣࠊ㍤Ⅼ࡟‽ࡎࡿࠋ
ణࡋࠊ෇≧ࡢ㯮Ⅼ࡟ࡘ࠸࡚ࡣⓑⅬࠊ㯮Ⅼ㸦෇
≧ࡢ≀㸧࡟‽ࡎࡿࠋ
ⓑⅬ㸦෇≧ࡢ≀㸧
඲㯮⾲♧⏬㠃࡟࠾࠸࡚ࠊ࿘㎶ྠⰍ⏬⣲ࡼࡾ᫂
ࡿ࠸࡜ㄆ㆑ࡉࢀࡿ෇≧ࡢⅬḞ㝗ࠋ
㐃⥆ⅬḞ㝗
㍤Ⅼࠊ㯮ⅬࡢⅬḞ㝗ࡀ」ᩘ࡟ࢃࡓࡾ㐃⥆ࡋ࡚
Ⓨ⏕ࡋ࡚࠸ࡿ≀ࠋ
㯮Ⅼ㯮Ⅼࠊ㍤Ⅼ㍤Ⅼࡢ࠸ࡎࢀࡢሙྜ࡟ࡘ࠸
࡚ࡶ㐃⥆ⅬḞ㝗࡜ࡍࡿࠋ
ୖᅗ౛࡛♧ࡍࡼ࠺࡟ࠊ㞄᥋ࡋࡓ5*ࡢ⏬⣲ࡀ
࡜ࡶ࡟Ḟ㝗㺢㺼㺍㺢ࡢሙྜ࡟㐃⥆ⅬḞ㝗࡜ࡍࡿࠋ
እほရ఩
ẼἻ㺂࢟ࢬ㺂␗≀
Ⅼⅉ඲ⓑࠊ඲㯮࣭㠀Ⅼⅉ࡟㛵ࢃࡽࡎㄆ㆑ࡉ
೫ගᯈ㺂㺜㺷㺂㺨㺼㺍㺖㺵㺐㺢ෆ ࢀࡿ≀ࠋ
እほ᳨ᰝ
ࢧ࢖ࢬࡢᐃ⩏
௙ᵝ᭩グ㍕ࡢᩘ್ࢆ‶ࡓࡉ࡞࠸≀ࠋ
෇≧ࡢ≀ࡢᐃ⩏ ⥺≧ࡢ≀ࡢᐃ⩏
㹢㸻㹟㸩㹠
ရྡ
᳨ᰝᇶ‽᭩ 1R
74&($)(<$$
࣮࣌ࢪ
7&*:9/3($11$1
㸧 ᳨ᰝᇶ‽
ศ㢮
ⅬḞ㝗
᳨ᰝ㡯┠
㍤ⅬḞ㝗
ุᐃᇶ‽
チᐜಶᩘ ಶ
㍤Ⅼ㛫ࡢ㊥㞳ࡣ PP ௨ୖ
㯮ⅬḞ㝗
チᐜಶᩘ ಶ
㯮Ⅼ㛫ࡢ㊥㞳ࡣ PP ௨ୖ
㐃⥆ⅬḞ㝗
㍤Ⅼࡢチᐜಶᩘ ⤌
㯮Ⅼࡢチᐜಶᩘ ⤌
㐃⥆ⅬḞ㝗 㐃⥆௨ୖ
㍤Ⅼࠊ㯮Ⅼඹ࡟࡞ࡁࡇ࡜
Ḟ㝗⥲ᩘ
ಶ௨ୗ
ⓑⅬࠊ㯮Ⅼ෇≧ࡢ≀
኱ࡁࡉPP
Gӌ
㸺Gӌ
㸺Gӌ
㸺G
チᐜಶᩘ
↓ど
ಶ
ಶ
ಶ
እほရ఩
೫ගᯈ࢟ࢬ
ᖜPP
:ӌ
㸺:ӌ
㸺:
ẼἻ㸦೫ගᯈ㸧
㛗ࡉPP
㸫
/ӌ
㸺/
㸫
チᐜಶ
↓ど
↓ど
ಶ
ಶ
኱ࡁࡉPP
Gӌ
㸺Gӌ
㸺Gӌ
㸺G
チᐜಶᩘ
↓ど
ಶ
ಶ
ಶ
኱ࡁࡉPP
Gӌ
㸺Gӌ
㸺Gӌ
㸺G
チᐜಶᩘ
↓ど
ಶ
ಶ
ಶ
␗≀㸦෇≧ࡢ␗≀㸧
␗≀㸦⥺≧ࡢ␗≀㸧
࢟ࢬ
ᖜPP
:ӌ
㸺:ӌ
㸺:
㛗ࡉPP
㸫
/ӌ
㸺/ӌ
㸺/
㸫
チᐜಶᩘ
↓ど
↓ど
ಶ
ಶ
͆෇≧ࡢ≀͇ཧ↷